Results for
STAPPERT INTRAMET SA
Belgium
Tube round welded, not annealed Tol. DIN EN ISO 1127, DIN EN 10217-7 TC1, grade 1.4301, 10-2 mm
Request for a quoteCIC - KLAUS CZERWONKA
Germany
With all the properties and variants of our standard cylinders DIN / ISO 15552. Completely made of stainless steel for use in harsh environments, marine, pharmaceutical and food industries.
Request for a quoteNORELEM FRANCE
France
Spline shafts based on DIN ISO 14 with straight parallel flanks. A spline shaft with spline hub is used to transmit high torques while enabling simultaneous axial movement. The spline shafts are colddrawn. Cold drawing does not interrupt the grain flow of the base material, ensuring spline shafts of very high strength. Tolerances Straightness 0.8 mm/m. Torsion max. 0.5 mm/m. On request Other lengths.
Request for a quoteNORELEM FRANCE
France
Universal joints with plain bearing can be swivelled by 45°. Max. transferable torque (Nm) at 150 rpm, operation angle α < 5°. * Bore depth is less than by DIN 808.
Request for a quoteNORELEM FRANCE
France
Connecting links for DIN ISO 606 duplex roller chains. By Form E, the spring clip must be mounted with the closed end facing the direction of movement. Offset links are required to close the chain if there is an odd number of links. Using offset links reduces the power and tensile strength by 20%.
Request for a quoteNORELEM FRANCE
France
Doubleacting pneumatic cylinder in constructionoptimised design acc. to DIN ISO 15552. Piston rod with external thread, position detection and adjustable pneumatic damping. Due to their robust construction, these cylinders are the preferred choice for numerous applications.
Request for a quoteNORELEM FRANCE
France
Hardened to 780 ±40 HV 10 and ground. Without leadin groove. Note All bushes have the bore size marked on the upper face, e.g. 10. Diameters D1 over 15 mm increase in size by 0.5 mm. Dowels or coiled spring pins together with DIN 1731 flathead screws can be used in place of the stop pin.
Request for a quoteNORELEM FRANCE
France
From diameter D1 over 15 mm size increases are 0.5 mm.
Request for a quoteNORELEM FRANCE
France
R-clips are used for securing bolts and axles. They are easy to install and can be reused. The ends have no sharp edges. Double coil R-clips have a flatter spring characteristics and are easier to install. The double coil allows a tether cable to be attached to prevent loss. Drawing reference: Form E: with single coil. Form D: with double coil (coil direction can differ from the drawing).
Request for a quoteNORELEM FRANCE
France
Steel, bright. Stainless steel A2, bright. Stainless steel A4, bright.
Request for a quoteNORELEM FRANCE
France
Steel, black oxidised. Stainless steel, bright. Note: Due to the better haptics, a larger pitch was chosen contrary to DIN. Drawing reference: Form A: without pin hole Form B: with pin hole Drill through and ream pin hole during assembly.
Request for a quoteNORELEM FRANCE
France
Tapped cylindrical pins are chiefly used in blind holes. The milled flat prevents air compression in blind holes. The tapping makes it possible to use the extractor 03328.
Request for a quoteNORELEM FRANCE
France
The dimensions of the dowel pin comply with DIN 6325. Advantages: Ideal for fixture construction Dimensionally stable even at high temperatures Electrically insulating
Request for a quoteNORELEM FRANCE
France
Parallel keys are used for the implementation of shaft-hub connections. These are positive connections which are used to transmit torque.
Request for a quoteNORELEM FRANCE
France
Hardened and ground, precision grade 1, paired tolerance IT 5, nominal dimensional tolerance DIN ISO 2768-mK On request: Several matched pairs.
Request for a quoteNORELEM FRANCE
France
Form A locating pins are used to position workpieces and fixture parts in reamed holes. The flattened Form C can be used to bridge tolerances in hole spacing or to secure the part to be positioned in one direction only. The Form A locating pins can also be used as limit stops or fixture feet. Advantages: Cerazur is extremely impact and bend resistant. The basis of this material is zirconium oxide. It is a composite metal-ceramic material. Drawing reference: Form A and B: cylindrical locating pin Form C and D: flattened locating pin
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
NORELEM FRANCE
France
For high demand hoisting and carrying tasks in safety-relevant areas (machine construction, load handling equipment, lifting tackle). The CE mark is impressed into the ring bolt. F2 permissible load under max. 45° per ring bolt. On request: Certificate of conformity.
Request for a quoteNORELEM FRANCE
France
From diameter D1 over 15 mm size increases are 0.5 mm. 1) Chamfer for insert
Request for a quoteNORELEM FRANCE
France
Stainless steel 1.4305. Version: Bright
Request for a quoteNORELEM FRANCE
France
Steel or 1.4305 stainless steel Version: Trivalent passivated. Stainless steel version bright. Note: LH thread refers to dimension D2.
Request for a quoteSTAPPERT INTRAMET SA
Belgium
Flatbars, hot rolled, heat treated, pickled, Tol. acc. DIN EN 10058, grade 1.4057 50/8 mm
Request for a quoteSTAPPERT INTRAMET SA
Belgium
Bars, Hexagone, cold produced, Tol. acc. to DIN EN 10278 (h11), grade 1.4057 QT800, 11 mm
Request for a quoteSTAPPERT INTRAMET SA
Belgium
Key Steel flat, drawn, tol. acc. to DIN 6880, grade 1.4571, 5-3 mm
Request for a quoteSTAPPERT INTRAMET SA
Belgium
DIN 2633 weld-neck flange, grade 1.4301 48.3 PN16 Form C
Request for a quoteSTAPPERT INTRAMET SA
Belgium
DIN 2527 blind flange, reduced thickness grade 1.4301 DN250, PN10, Form B
Request for a quoteSTAPPERT INTRAMET SA
Belgium
Coupling similar DIN 2987, grade 1.4571, 3/8"
Request for a quoteSTAPPERT INTRAMET SA
Belgium
Coupling similar DIN 2987, grade 1.4571, 1/4"
Request for a quoteSTAPPERT INTRAMET SA
Belgium
Welding collars, simílar DIN 2642, grade 1.4541, 42.4-2 mm
Request for a quoteResults for
Din - Import exportNumber of results
190 ProductsCountries
Company type
Category