Carbon steel strips - Import export

SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.

SURFACE FINISH. APPROVED FINISHES EN 10202 Bright, Fine stone, Stone, Silver, Matt COATING. PRECISE VALUES FOR TIN COATINGS EN 10202 HICKNESS TOLERANCES Thickness tolerances and edge reduction according to EN 10202 The thickness of the material must meet the following requirements: a) Deviation from the agreed thickness, measured on the centre line of the strip, must not exceed ± 5%. b) Deviation from the agreed thickness, measured at any point at a distance of no less than 6 mm from the sheared edge, must be between +5% and -8%. WIDTH TOLERANCES Other, closer dimensional tolerances are possible under a commercial agreement. EDGE CAMBER TOLERANCES Tolerances for edge bending under commercial agreement.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

11SMn30 EN 10087

HCXXXLA EN 10268

DC01 DC03 DC04 DC05 DC06 EN 10130 / EN 10139

THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES : Thickness tolerances according to EN 10051 for nominal widths. WIDTH TOLERANCES: Width tolerances according to EN 10051 for nominal widths Other, closer dimensional tolerances on request. EDGE CAMBER TOLERANCES: Sag tolerances according to EN 10051 for pickled hot-rolled strips will be agreed when placing the order. RIPPLE - LONGITUDINAL FLATNESS: The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm on 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness requirement must be agreed when placing the order.

THICKNESS TOLERANCES: According to the EN 10140:2006 Standard. Specified thickness tolerances for cold rolled strip and strip obtained strapping wide precision rolling w. WIDTH TOLERANCES: Width tolerances according to the EN 10140 Standard for nominal widths Other, closer dimensional tolerances are possible under a commercial agreement LENGTH TOLERANCES: According to the EN1040 Standard. Other tolerances are possible under a commercial agreement EDGE CAMBER TOLERANCES: Edge curve tolerances according to the EN 10140 Standard Other edge curve tolerances possible under a commercial agreement RIPPLE - LONGITUDINAL FLATNESS The flatness tolerance of the strips in cut lengths in the direction of rolling must be a maximum of 10 mm over 1000 mm. Any other flatness

FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement

FINISHES: SURFACE QUALITY PROPERTIES OF THE COATINGS GALVANISED STEEL according to EN 10142 Check our website for coating mass, coating finish, surface quality and protection surface treatment. If the customer does not require the surfaces to be oiled and/or chemically passivated, this must be clearly indicated when requesting the quote and placing the order. THICKNESS TOLERANCES Thickness tolerances according to EN 10143 for nominal widths. WIDTH TOLERANCES Tolerances on wide strips obtained by longitudinal cutting of a width of less than 600 mm.According to Standard EN 10143 of: w < 125; 125 w < 250; 250 w < 400; 400 w < 600. Other, closer dimensional tolerances under a commercial agreement. SAG TOLERANCES Edge curve tolerances under commercial agreement

Marcegaglia’s wide range of steel strips (HR, P&O) is engineered to match both standard and specialty requirements of target industry sectors. Thanks to its production and logistics features, Marcegaglia Baltics can create unique synergies for customers, integrating their supply chain and industrial processes creating purchasing efficiency, cost competitiveness (price optimization) and the development of more performing grades or products while guaranteeing the supply of existing codes.

Marcegaglia’s wide range of steel strips (P&O, CR, HDG) is engineered to match both standard and specialty requirements of target industry sectors. Thanks to its production and logistics features, Marcegaglia Baltics can create unique synergies for customers, integrating their supply chain and industrial processes creating purchasing efficiency, cost competitiveness (price optimization) and the development of more performing grades or products while guaranteeing the supply of existing codes.

- Wide range of steel grades: structural, cold forming, HSLA, etc. - In coils or cut-to-length - Standard os curtomized sizes

Production standart : EN 10051 FOR HR MATERIALS - S235 JR, S275 AND S355 QUALITIES EN 10139 FOR CR MATERIALS - DC 01 , ST 12 QUALITIES EN 10025 – 1