Bearing cases - Import export

DryLin® T linear guide systems were specially developed for applications in automation and handling systems. The design objective was a rugged linear guide for application in the most diverse - and also extreme - environments. They have the same dimensions as most recirculating ball bearing guides. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Profile rail and base body of the carriage made of aluminum. The rail is hard-anodized, the aluminum base body of the carriage is clear anodized. 2 Six gliding elements made of iglidur® J serve as guide bearings, which are positioned opposite to each other in pairs and make up 3 guide bearings. 3 Alternatively, bearing clearance is continuously adjustable 4 All steel parts are stainless steel 5 The lid is made of solid plastic or stainless steel DryLin® T - Technical data DryLin® T - Clearance adjustment DryLin® TWBM hand clamp DryLin® T - Design rules DryLin® T - Automatic clearance adjustment DryLin® linear guide systems in the cleanroom DryLin® T - Applications DryLin® T - System design DryLin® T - Installation videos System selection & service life calculation DryLin® T - Adjustable clearance The DryLin® T standard version is supplied preset and can be put into operation at once. The user can also manually adjust or fine-tune the clearance of the linear guide. The individual adjustment for your application, as well as the potential to respond to uneven screw surfaces through specific clearance allowance. DryLin® T - Adjustable clearance DryLin® T - Automatic DryLin® T carriages of the automatic version have a mechanism that automatically adjusts the bearing clearance after removal of the preload key. In case a bearing clearance of more than 0.13 mm has to be adjusted during operation, the bearing clearance automatically resets itself when the carriage is completely unloaded. DryLin® T - Automatic DryLin® TW-HKA manual clamp The manual clamp has been developed for simple tasks. The creep behavior of the clamped plastic causes a slackening in clamping force over time (up to 70%). Therefore safety-related parts should not be clamped. Please approach our applications consultant if you require other options for the clamping. DryLin® T - Manual clamping Drylin® T - Heavy Duty This series is used for the most extreme conditions such as dirt, adhesive residues, chips, mud, etc. The plastic gliding elements made of iglidur® J are fixed in the lid and are therefore non-detachable. This system is compatible with many standard commercial recirculating ball bearing systems and is available in the following sizes: TW-01-20, TW-01-25 and TW-01-30. DryLin® T Heavy Duty DryLin® T - Low-profile guide The clearance is not adjustable for the DryLin® T low profile guide rails. The gliding elements are mounted with positive fit in the chromated zinc carriage. This simple and effective design enables guides that are rugged and low-priced at the same time. DryLin® T - Low-profile guide DryLin® T - Compact linear guide This compact linear guide is suitable for rugged use (without clearance adjustment). This system has a slim design and the same dimensions as conventional recirculating ball bearing systems. The plastic gliding elements made of iglidur® J are fixed in the lid and are therefore undetachable. Suitable for DryLin® T guide rail of installation size 20. DryLin® T - Compact linear guide DryLin® TWBM - Manual clamping with high holding force This manual clamping is designed for a long-lasting high holding force of up to 500 N per clamping element. DryLin® TWBM hand clamp DryLin® T clamping elements for rail guide DryLin® T clamping elements for fast positioning by hand or with pneumatics. DryLin® T clamping element DryLin® T linear guide systems were specially developed for applications in automation and handling systems. The design objective was a rugged linear guide for application in the most diverse - and also extreme - environments. They have the same dimensions as most recirculating ball bearing guides. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Profile rail and base body of the carriage made of aluminum. The rail is hard-anodized, the aluminum base body of the carriage is clear anodized. 2 Six gliding elements made of iglidur® J serve as guide bearings, which are positioned opposite to each other in pairs and make up 3 guide bearings. 3 Alternatively, bearing clearance is continuously adjustable 4 All steel parts are stainless steel 5 The lid is made of solid plastic or stainless steel Advantages: 100 % lubricant-free Adjustable bearing clearance Automatic clearance adjustment High static load capacity Service life up to 50,000 km without lubrication High dirt resistance Low vibration and low noise When not to use ? When you want to save installation space drylin® N drylin® W When you need a pure stainless steel solution drylin® W drylin® R When you want to construct as economical as possible drylin® N drylin® W

igubal® rod end bearing, female thread With female thread in metric and inch dimensions igubal® rod end bearing, female thread igubal® rod end bearing, male thread With male thread in metric and inch dimensions igubal® rod end bearing, male thread igubal® rod end bearing CL For simplified mounting, with inner and outer threads in metric dimensions igubal® rod end bearing CL igubal® rod End Bearing CL DT For simplified installation, detectable with female thread in metric dimensions igubal® rod End Bearing CL DT igubal® fitting screw, mm Fitting screw with circlip igubal® fitting screw, mm When to use it? When you want to save weight When rotating, oscillating and linear movements should be implemented When high-frequency oscillations/vibrations predominate When a low-noise operation is desired When an electrically insulating part is required When freedom from corrosion is desired For combinations with pneumatic cylinders and gas struts When chemical resistance is required When high stiffening is required When not to use? When you have temperatures above +80°C (then HT options) When rotation speeds in excess of 0.5 m/s should be implemented When very high tensile and lateral loads prevail When applications should be implemented with hydraulic cylinder When dimensions over 30 mm are needed igubal® rod end bearing, female thread With female thread in metric and inch dimensions igubal® rod end bearing, female thread igubal® rod end bearing, male thread With male thread in metric and inch dimensions igubal® rod end bearing, male thread igubal® rod end bearing CL For simplified mounting, with inner and outer threads in metric dimensions igubal® rod end bearing CL igubal® rod End Bearing CL DT For simplified installation, detectable with female thread in metric dimensions igubal® rod End Bearing CL DT igubal® fitting screw, mm Fitting screw with circlip igubal® fitting screw, mm Special properties of the igubal® rod end bearings Maintenance-free, self lubricating High stiffening Very high fatigue strength in varying loads Compensation for alignment errors Compensation of edge loads Insensitive to dirt, dust and lint balls Resistant to corrosion and chemicals High dampening qualities Suitable for rotary, oscillating and linear movements Very low weight Dimensional series K and E, dimensions according to DIN ISO 12240 Version with metal sleeve in the spherical ball for enhanced torque Tolerances igubal rod end bearings can be used, according to the application, with different tolerances. They are designed with a large clearance in the standard product, which enables a secure operation even under high peripheral speeds. The bore of the inner ring has a tolerance according to E10. The shafts should have a tolerance between h6 and h9. Please contact us in case you require lower or more bearing tolerances. Loads igubal® rod end bearings take high forces in normal ambient temperatures, have excellent dampening properties and weigh only a fifth of the conventional metallic bearing housing. In particular cases the load carrying capacity of the rod end bearings should be checked in a practical trial especially with high constant loads and at higher temperatures. Coefficients of surface friction and speeds Rotary motions of the mounted shaft take place directly in the bearing ball made of iglidur® W300. The advantage of this plastic/steel plain bearing is that high speeds can be achieved in dry operation. Taking the radial loads into account, maximum surface speeds up to 0.5 m/s rotating can be attained. The maintenance-free igubal® rod end bearings casually permit linear and oscillating movements of the shaft. Delivery program igubal® rod end bearings are available in the dimensional series K and E for shaft diameters of 2 to 30 mm in all dimensions according to DIN ISO 12240, and of course respectively in the Form A - with male thread and Form B - with female thread The dimensional series K and partly E are moreover available in inch dimensions and – as special version – with a stainless steel sleeve in the spherical ball. Thereby an essentially higher tightening torque is possible than with the plastic spherical ball. Please ask us for other sizes. igubal® rod end bearings - Applications igubal® rod end bearings - Applications Temperatures Dimensional series K in A+B variants for temperatures upt to +200°C (HAT material).

F2CFE614E A004, F2CFE614A B001, F2CFA613A E001, F2CFP613A H001, A8000, F2CFP614A H001, A8800