Automatic loading - Import export

DryLin® T linear guide systems were specially developed for applications in automation and handling systems. The design objective was a rugged linear guide for application in the most diverse - and also extreme - environments. They have the same dimensions as most recirculating ball bearing guides. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Profile rail and base body of the carriage made of aluminum. The rail is hard-anodized, the aluminum base body of the carriage is clear anodized. 2 Six gliding elements made of iglidur® J serve as guide bearings, which are positioned opposite to each other in pairs and make up 3 guide bearings. 3 Alternatively, bearing clearance is continuously adjustable 4 All steel parts are stainless steel 5 The lid is made of solid plastic or stainless steel DryLin® T - Technical data DryLin® T - Clearance adjustment DryLin® TWBM hand clamp DryLin® T - Design rules DryLin® T - Automatic clearance adjustment DryLin® linear guide systems in the cleanroom DryLin® T - Applications DryLin® T - System design DryLin® T - Installation videos System selection & service life calculation DryLin® T - Adjustable clearance The DryLin® T standard version is supplied preset and can be put into operation at once. The user can also manually adjust or fine-tune the clearance of the linear guide. The individual adjustment for your application, as well as the potential to respond to uneven screw surfaces through specific clearance allowance. DryLin® T - Adjustable clearance DryLin® T - Automatic DryLin® T carriages of the automatic version have a mechanism that automatically adjusts the bearing clearance after removal of the preload key. In case a bearing clearance of more than 0.13 mm has to be adjusted during operation, the bearing clearance automatically resets itself when the carriage is completely unloaded. DryLin® T - Automatic DryLin® TW-HKA manual clamp The manual clamp has been developed for simple tasks. The creep behavior of the clamped plastic causes a slackening in clamping force over time (up to 70%). Therefore safety-related parts should not be clamped. Please approach our applications consultant if you require other options for the clamping. DryLin® T - Manual clamping Drylin® T - Heavy Duty This series is used for the most extreme conditions such as dirt, adhesive residues, chips, mud, etc. The plastic gliding elements made of iglidur® J are fixed in the lid and are therefore non-detachable. This system is compatible with many standard commercial recirculating ball bearing systems and is available in the following sizes: TW-01-20, TW-01-25 and TW-01-30. DryLin® T Heavy Duty DryLin® T - Low-profile guide The clearance is not adjustable for the DryLin® T low profile guide rails. The gliding elements are mounted with positive fit in the chromated zinc carriage. This simple and effective design enables guides that are rugged and low-priced at the same time. DryLin® T - Low-profile guide DryLin® T - Compact linear guide This compact linear guide is suitable for rugged use (without clearance adjustment). This system has a slim design and the same dimensions as conventional recirculating ball bearing systems. The plastic gliding elements made of iglidur® J are fixed in the lid and are therefore undetachable. Suitable for DryLin® T guide rail of installation size 20. DryLin® T - Compact linear guide DryLin® TWBM - Manual clamping with high holding force This manual clamping is designed for a long-lasting high holding force of up to 500 N per clamping element. DryLin® TWBM hand clamp DryLin® T clamping elements for rail guide DryLin® T clamping elements for fast positioning by hand or with pneumatics. DryLin® T clamping element DryLin® T linear guide systems were specially developed for applications in automation and handling systems. The design objective was a rugged linear guide for application in the most diverse - and also extreme - environments. They have the same dimensions as most recirculating ball bearing guides. Technical data Gliding elements: Maintenance-free Material: iglidur® J * Max. surface speed: 15 m/s Operating temperature: -40°C to +90°C *Other materials on request 1 Profile rail and base body of the carriage made of aluminum. The rail is hard-anodized, the aluminum base body of the carriage is clear anodized. 2 Six gliding elements made of iglidur® J serve as guide bearings, which are positioned opposite to each other in pairs and make up 3 guide bearings. 3 Alternatively, bearing clearance is continuously adjustable 4 All steel parts are stainless steel 5 The lid is made of solid plastic or stainless steel Advantages: 100 % lubricant-free Adjustable bearing clearance Automatic clearance adjustment High static load capacity Service life up to 50,000 km without lubrication High dirt resistance Low vibration and low noise When not to use ? When you want to save installation space drylin® N drylin® W When you need a pure stainless steel solution drylin® W drylin® R When you want to construct as economical as possible drylin® N drylin® W

Available in different sizes and for film webs from 310 mm to 610 mm. Optionally with roller knife cut for soft blisters or die-cutting tool for hard blisters. Additional equipment options for online printing, vacuum, MAP, automatic loading system and much more.

This series machine is designed and manufactured specifically for the switching industry 2 Automatic feed terminal, loaded terminal / screwing / complete 3. Automatic detection,auto start when there is material, auto cut off when no material detected 4. Automatic counting, set output 5 Using the touch screen, intuitive interface, simple and safe operation 6 Reporting irregular operation and giving the relative solutions in the form of message.

SCR Power Controller Unit suitable for resistive and medium or long wave infrared loads Current range – 30A, 35A, 40A, 60A, 75A, 90A, 120A, 150A, 180A, 210A, 300A, 350A, 400A, 450A, 500A, 800A Voltage Range 480V, 600V and 690V (starting from 60A) Fully isolated from the power Zero crossing firing mode (ZC) or Burst Firing (4, 8 or 16 cycles selectable) Logic input signal 4 to 30V DC typical (SSR) plus 4-20mA or 0-10V DC Linear input as an option Constant current drain, independent of supply voltage with SSR input Heater Break (HB) alarm to diagnose partial or total load failure with automatic setting, relay alarm output and front LED indication. Available as an option Side by side mounting Special design Heatsink with high dissipation value IP20 protection Complies with EMC, EAC, cULus® 508 listed and cUL® listed up to 500A as an option. UL® for 800A as an option.

REVO S 2PH Thyristor Power Controller is suitable for resistive and medium or long wave infrared loads Current range – 30A, 35A, 40A, 60A, 75A, 90A, 120A, 150A, 180A, 210A, 300A, 400A, 450A, 500A, 600A, 700A, 800A Voltage range 480V, 600V and 690V (starting from 60A) Fully isolated from the power Zero crossing firing mode (ZC) or Burst Firing (4, 8 or 16 cycles selectable) Logic input signal 4 to 30Vdc typical (SSR) plus 4-20mA or 0-10Vdc Linear input as an option Constant current drain, independent of supply voltage with SSR input Heater Break (HB) alarm to diagnose partial or total load failure with automatic setting, relay alarm output and front LED indication. Available as an option Side by side mounting Special design Heatsink with high dissipation value IP20 protection Complies with EMC, EAC, cULus® 508 Listed and cUL® listed up to 700A as an option. UL® listed for 800A as an option.

V79 : a model with innovative ergonomics : no pit for the press, no platform for the operator. This customized V79 is used for large volume bi-material injection with automatic loading and demolding.

Removing the roller tracks by independent heating up to 220 ° C Adjustable speed of laying tracks up to 5 m / min Manual loading of sheets Side guides adjustable micrometer Winding device holder with the magnetic track detection cell in case of breakage. Mounting Tape with voltage control, and adjustable positioning guides the rollers. Positioning + or 0.1 mm servo motor 0,75 KW Cleaning system with a double face support roller on the output Storage formats tracked on a table with two anti static positioned before the guillotine and before the table Touch screen control friendly, multi lingual (French and / or English), setting and trimming various counts Use of electrical, hydraulic and pneumatic standardized Safety guards for strict compliance with CE OPTIONS MTL 700 NSA automatic loading of sheets Roller and additional heating system for a different bandwidth

PicoFill Add-on is a very compact and flexible filling system for CO 2 / N 2O in combination with other Filltech systems like uniFill. Highlights Easy, precise and safe to operate For operation in combination with other Filltech systems Individual solutions on demand Optionally available with integrated pump or for central pumping supply Different attachment parts and filling adapters for the filling of several cylinders in the indicated weight range Additional case for accessories and tools Short set-up time for changing parts Technical Data Filling-range: approx. 50 g - 6 kg/ up to 13 lbs. fill weight Weighing-range: up to 15kg / 35 lbs. Scale division: 0-7 kg -2 g, 7-15 kg - 5 g Dimensions: approx. 600 x 400 x 1200 mm/ 24 x 24 x 47.5 in. Weight: approx. 50 kg/ 110 lbs. Weighing System Two load cells Automatic tare setting Automatic shut-off at target weight Legal for trade Technical Data Filling-range: approx. 50 g - 6 kg/ up to 13 lbs. fill weight Weighing-range: up to 15kg / 35

Avery compact and flexible filling system for CO 2/N 2O in combination with other Filltech systems like profiFill or uniFill. Highlights Easy, precise and safe to operate For operation in combination with other Filltech systems Individual solutions on demand Optionally available with integrated pump or for central pumping supply Different attachment parts and filling adapters for the filling of several cylinders in the indicated weight range Additional case for accessories and tools Short set-up time for changing parts Technical Data Filling-range: approx. 50 g - 6 kg/ up to 13 lbs. fill weight Weighing-range: up to 15kg / 35 lbs. Scale division: 0-7 kg -2 g, 7-15 kg - 5 g Dimensions: approx. 600 x 400 x 1200 mm/ 24 x 24 x 47.5 in. Weight: approx. 50 kg/ 110 lbs. Weighing System Two load cells Automatic tare setting Automatic shut-off at target weight Legal for trade Technical Data Filling-range: approx. 50 g - 6 kg/ up to 13 lbs. fill weight Weighing-range: up to 15kg / 35 lbs. Sca