Dimmers - Import export

With rotary control, two-way switch and soft-catch. 2-wire connection (neutral conductor not required) Optimised for dimming of retrofit LED lamps (LEDi). For dimmable Retrofit-LEDs (LEDi). For dimmable Retrofit-LEDs (LEDi) with conventional or electronic transformers. For incandescent lamps, 230 V tungsten halogen lamps, low-voltage halogen lamps with conventional or electronic transformers and dimmable energy-saving halogen lamps. Mix operaton of LEDi with conventional loads possible. Via mode switch adjustable between leading edge control and trailing edge control. Low-noise level by MOSFET transistors. With electronic short-circuit protection. With electronic overload protection. With adjustable minimum brightness. Without cover plate. Rated voltage: 230 V~, + 10% / - 10% Rated frequency: 50 Hz/60 Hz Nominal power: 2 - 100 W/VA (retrofit LED loads). Nominal power: 10 - 250 W/VA (non-LED loads).

Very small installation depth: < 20 mm Without claws. With rotary control, two-way switch and soft-catch. 2-wire connection (neutral conductor not required) Optimised for dimming of retrofit LED lamps (LEDi). For dimmable Retrofit-LEDs (LEDi). For dimmable Retrofit-LEDs (LEDi) with conventional or electronic transformers. For incandescent lamps, 230 V tungsten halogen lamps, low-voltage halogen lamps with conventional or electronic transformers and dimmable energy-saving halogen lamps. Mix operaton of LEDi with conventional loads possible. With manually adjustable operating mode: trailing / leading edge control. With adjustable minimum/maximum brightness. Low-noise level by MOSFET transistors. With electronic short-circuit protection. With electronic overload protection. Without cover plate. Rated voltage: 230 V~, + 10% / - 10% Rated frequency: 50 Hz/60 Hz Nominal power: 2 - 100 W/VA (leading edge control) Nominal power: 2 - 400 W/VA (trailing edge control)

Dims streetlights to pre determined levels throughout the night. Saves up to 60% energy consumption. Works will all DALI2 D4I LED Drivers. Works with TE Zhaga Motion sensor switching light on at 20% power output, increasing to 100% on detection of motion, returning to 20% power output after 2 minutes. ANSI & Zhaga Book 18 compatible

A dimmer is a device designed to vary the brightness of an artificial light source. F/ART has designed the "DIMMER LCU" specifically for cold cathode tubes (neon) powered exclusively by electromagnetic transformers, such as Resinblock.

The Ekinex® actuator / dimmer is an S-mode modular KNX device for panel mounting, able to command and regulate the brightness of lighting devices. In order to function properly, the device has to receive a telegram from the bus, sent by a KNX sensor (for example a pushbutton, a sensor or another command/control device) or another KNX command device, which opens or closes the corresponding relay or regulates the brightness of the connected lighting device.

With the DIMMbox, FRIWO offers a technically sophisticated solution for dimming LED lighting. Different versions of the DIMMbox enable dimming per DALI, Push-Dim or 1 - 10 V. The dimming function is achieved by pulse width modulation control (PWM) with a switching frequency of 600 Hz. There are no flicker effects due to the chosen frequency. The DIMMbox works with a voltage range from 15 to 50 VDC and a current of 5 A at input and output. The device can be operated in constant voltage- or constant current mode in connection with FRIWO LED drivers. Furthermore, the DIMMbox is connectable to all third party drivers in constant voltage mode. With a length of 153 mm and a minimum cross section of 21 x 30 mm, the DIMMbox can be used for smallest profiles. The DIMMbox is approved for Europe and complies with the low voltage directives EN61347-1, EN61347-2-11 and EN60065 as well as with the EMC directives EN55015, EN55022 and EN61547.