Concrete anchor - Import export

The wedge anchor is hammered into the borehole, with the expansion clip resting against the borehole wall due to its internal stress. When the nut is tightened, the cone pulls into the expansion clip, spreads it and presses it against the building material.

They provide excellent protection for pallet racks, corners, and columns that may be in warehouses. Guards help reduce or prevent damage. Pallet covers are required for fixed rack installations where industrial trucks are used (except when guided by rails). Pallet rack covers are the perfect solution in most situations. They can also be used to protect machines, rectangular columns, etc. Easy to install, the covers can be bolted directly to the concrete with mounting anchors and provide immediate protection for nearby resources. Each guard is a powder-coated yellow to ensure excellent visibility during operation.

This stainless steel anchorage point (Ø 16 mm) - designed to secure individuals - has been certified by the German Institute for Construction Technology (DIBt). It is installed in concrete using two-component adhesive and is suitable for installation on a roof surface or facade - on the ground, in a wall or overhead. National technical approval ("abZ"): Z-14.9-688 (pls. observe the provisions provided in the "abZ") EN 795:2012, A + CEN/TS 16415:2013 Concrete ≥ C20/25 Recommended accessories: Special adhesive WIT-VM-250 Important: When the device protudes ≥ 100mm above the subsurface in a wall/facade lifeline system (corner or end support), an additional supporting tube is required

This reinforced, stainless steel anchorage point - designed for concrete applications - does not create any tension in the substructure and is suitable for unprotected surfaces. It includes a base plate (150 x 150 mm) and a welded-on supporting tube (Ø 42 mm) for extra stability and is installed using the 4 anchor rods supplied. All you need is an installation depth of a mere 60 mm. EN 795:2012, A + CEN/TS 16415:2017 Base plate + welded-on supporting tube Concrete ≥ C20/25 For installation depths ≥ 60mm Recommended accessories: Special Adhesive WIT-VM-250 Incl. stainless steel installation set

This stainless steel anchorage point (Ø 16 mm) was specially developed with a larger base plate (370 x 370 mm) for installation in lightweight or porous concrete. The 8 anchor rods supplied in the package are cemented permanently into the concrete substructure using special adhesive. EN 795:2012, A + CEN/TS 16415:2013 Porous concrete ≥ P3.3 Add a supporting tube for usage as an end or corner post in a lifeline system Recommended accessories: Special Adhesive WIT-VM-250 Incl. stainless steel installation set

At first,the ground of field is hardened for leveling by steamroller or ground roller. For ground concrete,the place is excavated by JSB or etc. The concrete is poured to the excavated area. 25cmx50 cm molds are placed. The reinforcing bars are placed into the molds. Before pouring the concrete,anchor pipes are put amoung the reinforcing bars.After pouring the concrete,the gravels are poured up to the zero point as No:4 , No:3, No:2 sequintally.76mmx3mm thick h:600 cm verizontal pipes are placed.After placing all pipes,60mmx2mm thick horizontal pipes are welded to the vertical pipes. Vertical and horizontal pipes are painted with anticorrosion paint. Over the anticorrosion paint,RAL 6005 paint is applied. Then the area is enclosed with 50cmx50cm sized 3,50 mm thick PVC wire mesh. 55 mm thick artificial turf is roll outed. Silica sand and sbr granuls is applied into the turf. Sport equipments,goalposts,top covering mesh,lighting projector and projector posts are installed.

Rotafix Zeroset Anchor Grout is a 2-part high strength epoxy system that is used for the fixing of metallic objects into concrete such as anchors and studs. Rotafix Zeroset Anchor Grout has been specifically designed for setting at low temperatures in smooth-walled, diamond drilled holes. This chemical anchor will displace water from a hole then cure under any residual water. This high-performance chemical anchor grout has been approved by the Department of Transport for parapets and street lighting. Additional Information: Compressive Strength: 70N/mm2 Tensile Strength: 16N/mm2 Flex Strength: 32N/mm2 Workable for 20 minutes at 20°C Available Sizes: 500cc (Product code: 3542)

This floating fountain is easy to install and does not require construction works. Its compact size makes it easy to install in a pond - just connect the device to the control panel. The fountain provides aeration of the water, prevents the growth of algae. Additional options (such as lighting) are not included in the set. They can be ordered separately. The fountain is equipped with a valve that allows you to change the jets heights manually. In order to automatically change the jets heights, the fountain can be connected to a frequency converter (additional option). Automatic switching on and off of the fountain and lighting (not included) is performed by the Siemens controller. Equipment: 1. Floating module made of stainless steel 2. Pump in a stainless steel filter casing 3. Fountain nozzle 4. 8 pins for fixing the lighting fixtures 5. Underwater cable - 50 m. 6. 4 concrete anchors in a polymer sheath, rope, carabiners. 7. Weatherproof fountain control cabinet, IP66.

The tie points for the one-sided tie rod equipment can be operated by just one person - this guarantees optimised working even with less manpower requirements and in confined spaces. The new system has the particular advantage of being able to be anchored either on one side or conventionally, depending on requirements.