Component wire - Import export

Testing requirements for a manufacturer in electronics industries had changed: For an assembly included in a smartphone, the absence of contact between speaker ultra fine wires and adjacent components is essential. Fulfillment of this condition, until now only subjected random sampling by microscopy, from now on has to be verified in a 100% procedure. Due to labor cost, microscopy for this amount of inspection is no more lucrative. Detection of ultra fine wires in electronic device The particular challenge The fine wires made of copper in smartphone speakers dispose of a high reflection and only a small diameter. The QuellTech Solution A high-resolution QuellTech 2D/3D Q4-5 Laser, featuring a particularly adapted laser wavelength and an ultrafine laser line in the corresponding installation, is combined with a linear axis equipped with a convenient encoder output. Due to its special chip analysis, the Quelltech sensor delivers a stable and highly reproducible signal on the fine wires

Tweezers for handling and assembly of cylindrical components ¯ 2mm, Length 120mm

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The wire facilitates very flexible installation. The fibreglass insulation facilitates routing the probe along very hot components (Tmax. 450 °C). The thin probe tip guarantees very rapid response. Temperature range: -100 °C to +450 °C Wire type: Fibreglass/fibreglass, 0.5 mm, wire, Tmax: +450 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The thin wire, barely 0.7 mm in diameter, facilitates highly flexible installation. The thin probe tip guarantees very rapid response. Temperature range: :-190 °C to +260 °C, short-duration to +300 °C Wire type: Teflon,0.08 mm, wire, Tmax: +300 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The thin wire, barely 2 mm in diameter, facilitates highly flexible installation. The thin probe tip guarantees very rapid response. Temperature range: -100 °C to + +200 °C, short-duration to + 230 °C Wire type: Teflon, 0.2 mm, wire, Tmax: +200 °C

This inline thermocouple can be individually installed. For measurements in the wiring harness, on difficult to access points or on the smallest components. The thin wire facilitates very flexible installation. The fibreglass insulation facilitates routing the probe along very hot components (Tmax. 450 °C). The thin probe tip guarantees very rapid response. Temperature range: -100 °C to +450 °C Wire type: Fibreglass/fibreglass, 0.2 mm, wire, Tmax: +450 °C

Forms the component wire in C-shape and cuts the residual part at 4mm. ESD. Steel thickness 3mm, Length 150mm

Forms the component wire in C-shape and cuts the residual part at 4mm. ESD. Steel thickness 3mm, Length 150mm

We employ welding robots to join complex metal wire parts made of steel or aluminium to form an assembly. This in turn leads to complex bent wire components for the automotive industry, such as brackets for cushioning frames, and eyelet fastenings.

As a competent industrial partner, we produce stamped, bent-wire and formed components from stainless steel, non-ferrous metals and regular steel in a consistent quality. Dependability and flexibility characterize our performance. Our experience and technical know-how enable fast response and economical pricing. Benefit from the experience our staff have gathered with these products. We can competently process small as well as large orders. Possible material thicknesses: 0.5 to 4.5 mm. Possible materials: Regular steel, stainless steel, brass, copper, light metals. Available with all standard surfaces.

Tyrolit's diamond saw wires match the high performance of our customers in the construction industry. Designed for maximum productivity, each wire delivers powerful performance, user-friendliness, and top results. Combined with Hydrostress machines, Tyrolit offers complete system solutions ideal for cutting complex steel and reinforced concrete structures, making them perfect for demolishing buildings, bridges, and large reinforced concrete components. Tyrolit's diamond wires ensure reliable, safe, and efficient performance for every application, whether electroplated or sintered. Our range also includes spliced saw wires without sleeves. Notably, Tyrolit offers the world's only ATEX-certified wire saw system for Zone 1 explosion-hazardous areas, providing high safety and performance in explosive environments. Tyrolit also provides a comprehensive range of accessories to enhance wire saw efficiency, ensuring first-class quality and innovative solutions since 1919.

With over 125 years of market experience, a network of specialised companies has evolved to serve the wide range of your customers’ requirements with the best possible quality. The focus of these long-standing cooperations is on making the most of available know-how while maintaining fair market prices. Besides bent wire and plastic components, a wide range of industries also require so-called hybrid parts. This combination of metal and plastic is found, for instance, in screw joints, connecting rods, seat elements for lumbar support, and medical engineering, among other areas. We work in close cooperation with specialised partners for plastics engineering. Our great efficiency in wire working technology and plastic injection enables us to create hybrid parts that satisfy the most stringent requirements.

Gross Weight: 0.2kg Material: Milk wire rack Main Component Content Of Fabric: 81% (inclusive)-90% (inclusive) Pattern: printing Style: ins wind Sleep Length: long sleeves Version: Slim-type Length: Medium length (65cm＜clothing length≤80cm) Material Ingredients: 81%-90% Material 2 Ingredients: 10%-29%

Discover the precision and versatility of our cold extrusion wires at Vom Hofe Kaltstauchdraht GmbH - your first-class source for high-quality wire solutions. Our cold extrusion wires combine advanced technology, highest quality and first-class performance for demanding applications. Outstanding precision and versatility for diverse applications: Our cold extrusion wires are characterised by their outstanding precision and versatility, making them the ideal choice for a wide range of applications. Whether in the production of fasteners, drawing parts or other demanding components - our cold extrusion wires fulfil the highest requirements.

Equipped with CAN or CANopen interfaces and a 19″ slide-in casing, the MicroControl µLAB is particulary suitable for measuring electric, thermal and mechanic signals in engine or components testing facilities. The signal wires are connected to the module by plug-in connectors in the front plate.

Equipped with CAN or CANopen interfaces and a 19″ slide-in casing, the MicroControl µLAB is particulary suitable for measuring electric, thermal and mechanic signals in engine or components testing facilities. The signal wires are connected to the module by plug-in connectors in the front plate.

Equipped with CAN or CANopen interfaces and a 19″ slide-in casing, the MicroControl µLAB is particulary suitable for measuring electric, thermal and mechanic signals in engine or components testing facilities The signal wires are connected to the module by plug-in connectors in the front plate.

Central Cooling System or Rack Compressor System consist of several compressors,for graduated adaption to your capacity requirement.The compressors work in parallel connection on a common refrigeration circuit. It goes without saying that we have a high vertical range of manufacture with fully-hermetic, scroll and digital scroll, semi-hermetic and screw compressors from different manufacturers. According to your requirements we supply rack units with a wide selection of optional components, electrically pre wired or with switch cabinet. We also offer the ideal control system adapted to each individual application. This system mostly using for more than 3 rooms cold storage plant. Technical Specification It has semi hermetic, scroll or screw type compressor. Be manufactured with air cooled or water cooled condenser. All equipment are delivered together with control instruments as being ready to assembly.

We continuously develop our production facilities for different forms of animal husbandry. Our wire mesh components serve sustainable and long-lasting cave systems with high corrosion protection.

Wire Belt Company’s Chain Link belting is the simplest available wire belt design, suitable for light duty use in drying and cooling applications. Chain Link is a component part of Wire Belt Company’s Troughing Filter Belts, and can also be used as collapsible screen for applications such as lift guards.

High performance heat reflective aluminium backed glass cloth, single coated with a high temperature pressure sensitive silicone adhesive. Thickness:0.2mm; silver Very good temperature resistance.SAE J2302 Thermal Effectiveness at 550°C is 107°C (other testing results available on request).High tensile strength.Halogen-free.Lead-free.Conforms to European Directives 2000/53/EC for End of Vehicle Life (ELV) recycling (does not contain heavy metals) and 2002/95/EC (RoHS).Excellent chemical compatibility with most materials used in components for wiring.

AMETEK Specialty Metal Products has built a reputation for first class product quality and reliability, and that’s why so many leading commercial and defense aviation programs use our high performance materials. 50 years Aerospace Expertise We have more than 50 years experience developing precision strip, wire and shaped component products for critical aerospace applications worldwide. Our aerospace portfolio includes: High Tolerance Custom Shaped Wire for Aircraft Push-Pull Controls Pfinodal® (C72900) Bearing Material for Landing Gear Bushings and Bearing Sleeves Specialty Shaped Wire for Lock Collar Tape used in Aerospace Rivets Highly Conductive Nickel Strip for Aerospace Electronic Connectors, Batteries, Heat Exchangers and Bellows. Lighter and Stronger Materials for Aircraft Performance At 35,000 feet, every detail matters. We’re dedicated to manufacturing precision, lightweight and high strength materials to enhance the performance and efficiency of aircraft worldwide.

The Dexnyl PEEK shrink tube provides a protective layer for sensitive or critical components as an alternative to traditional materials. PEEK shrink tubes are particularly effective in environments where extreme heat or cold, high pressure, or chemicals, water, or dielectric interference endangers wires and electrical components. BIEGLO can offer PEEK shrink tubing with a diameter of 0.965mm to 9.957mm. PEEK is a thermoplastic polymer that is commonly used instead of metal or other types of plastics. PEEK has a temperature resistance of up to 240 ° C and a special resistance to chemicals.

A flexible dual wall, radiation cross linked tubing used for insulating, jacketing and bundling of wire harnesses and components. Ideal for sealing connector to cable transitions and similar moisture proofing applications. Made from flame retardant polyolefin, MIL and UL rated*, it offers a good balance of sealing and protection against fluids on transitions to connectors. Shrink Ratio 3 1 or 4 1 Operating Temperature Range 55°C to 125°C

A highly flexible, flame retarded, radiation cross linked tubing used for insulting, jacketing and bundling of wire harnesses and components. A high shrink ratio accommodates difficult or irregular shapes. Shrink ratio 3 1 or 4 1 Operating Temperature Range 55°C to 125°C

A highly flexible, zero halogen tubing used for insulating, jacketing and bundling of wires, harnesses and components. Made from flame retardant polyolefin, it has excellent electrical, chemical and physical properties. Suitable for applications requiring low smoke emissions. Shrink Ratio 2 1 Operating Temperature Range 30°C to 125°C Zero Halogen

Plotter with plates for PARTEX neutral wire, cable, component and terminal markers. Print Printing method: Plotter pens with etching ink Drawing speed: Max 40mm/s (1.57 tum/s) Temperature range Working temperature: +10ºC to +35ºC ( 50ºF to 95ºF) Storage temperature: -10ºC to +50ºC ( 14ºF to 122ºF) Recommended profile temperature: +20°C ( 68ºF) Resistance The products intended for MK500 is tested according to Partex Product Test Programme by the Swedish Test and Research Institute. Mark Type Groups MK500 print on : Wire markers PA+02 PA+1 PA+2 Open wire markers PC-10 PC-20 PC-30 PC-40 Cable markers PK2 POH Component markers PN PS Terminal block marking TX-61 TX-96

Avicenna Technology is a leading provider of laser ablated fine wire and laser machine polymer tubing for the medical device market.

Polymer catheter shafts and components, as well as insulated wire and cable, can be precisely machined through non-contact laser ablation.