Voltage - Import export

"Our stock consists of about 100 transformers (low and high voltage) up to 3MVA that can be rented or sold. We find power transformers in different types of applications: in electrical transmission networks, in electrical distribution and in factories. Characteristics of high voltage transformers: - 2 types of cooling: dry and oil - Transformers supplied up to 10MVA - Extra low loss design for the European market or other lossy design for export - Aluminium or copper windings - Special design for special application on request - Rental possibility: Our transformers can be rented for construction sites or for repair purposes."

"Our stock consists of about 40 transformers (low and high voltage) up to 3MVA that can be rented or sold. We find power transformers in different types of applications: in electrical transmission networks, in electrical distribution and in factories."

"Our stock consists of about 100 transformers (low and high voltage) up to 3MVA that can be rented or sold. We find power transformers in different types of applications: in electrical transmission networks, in electrical distribution and in factories. Characteristics of low voltage transformers: - 2 types: isolation transformers and autotransformers - Three-phase dry-type transformers delivered up to 2000 kVA Mainly available in 230/400V or 400/400V or 400/500V or 400/690V - Other primary and secondary voltages on request - Stored as new up to 160 kVA - With or without IP20 protection cover - Aluminium or copper windings - Special design for particular application on request - Rental possibility: Our transformers can be rented for construction sites or for repair purposes."

"The high voltage motors can be made of cast iron or welded steel (lighter solution). HIGH VOLTAGE MOTORS WITH CAGE: - Three-phase motors with cast iron cage - High voltage motors between 3 and 13.8kV - Power from 160kW to 10MW - IP55 or IP23 protection - Efficiency IE3/IE4 (tomorrow IE5) - Standard or custom sizes are available for sale - 2-4-6 poles stocked motors up to 1,2MW, IC411 cooling - Customized motors according to your specifications or to replace an existing motor will be delivered to you - Cooling mode IC411-IC416-IC511-IC611-IC616-ICW81 - Ball or sleeve bearings"

"Slip ring motors are often used in applications where the maximum transient torque must be greater than a conventional cage induction motor, such as quarries. SLIP RING MOTORS (OUR CODE: MB) - Three-phase wound rotor motors - Standard cast iron housing - Stored in IP55 protection and on request in IP23 - Stored in 230/400V from 22kW to 315kW , 400/690V to 560kW - Operating in 50/60hz - Other special voltages or insulation class H on request - Form B3-B5-V1- B35-V15 - Stored in S1 service or S3 service (6 starts per hour) - On request, we can supply motors for lifting applications with 1 or 2 cylindrical or conical axes - Standard motors equipped with PTC sensors - Equipped with roller bearings for belt drive - Electrolytic starters are stocked to start these motors"

Measurement transmitter designed to convert any notnormalised DC voltage or current signal into a normalised signal while providing galvanic insulation. o Voltage or current input o Galvanic isolation 2 kV RMS. 50 Hz during max. 60 s between input, output and power supply o Selection of input and output ranges by jumpers behind the front plate o Wide range of power supplies o Rail DIN mounting Compliant with EMC EN 500822

This circular motorised damper is suitable for ducts with 125 mm. The position of the damper blade can be set via Modbus RTU communication or a 0-10 V signal. The enclosure has an airtightness class D according to EN1751. To ensure this classification aluminium tape should be wrapped on the seam between damper/duct. The unit needs 24 VDC supply voltage. We recommend using Sentera 24 VDC power supplies with RJ45 connector. They are protected against overload, overvoltage and short circuit. Once installed the device is ready for use. The default settings will suffice for most applications. If you do need to change some parameters, this can be done via Modbus RTU communication.

This self-calibrating CO2 sensor measures CO2 as well as temperature, relative humidity and ambient light conditions. It needs a 24 VAC supply voltage. This sensor can also directly control an EC-fan, AC fan speed controller or frequency inverter. It has 1 single analogue / modulating output depending on the highest measured value for temperature, humidity or carbon dioxide. If you only want to use it for measuring CO2, you can deactivate the temperature or humidity measurement. The FCMFX-series are available for different types of supply voltages such as 24 VDC, 24 VAC/VDC or 230 VAC. All version have 3 LEDS on the frontpanel showing whether the measured value is within or out of range. Additionally they are available in a version with audible alert. All parameters are accessible via Modbus RTU. This sensor doesn't need to be configured. Once installed it's ready for use.