Variable speed - Import export

"The demand for speed control has taken off with the advent of IGBTs and powerful microprocessors. Today, there is no longer any difference between DC and AC. 99% of new installations will be equipped with variable speed AC solutions. In our product range, we have both DC and static frequency inverters. Characteristics of a DC drive: - Three-phase power supply between 200 and 690V - Digital inverter - 2 and 4Q solution - Power between 2.4kW and 3.2MW - IP20 protection - Modular drive for cabinet mounting - We have a stock only in 4Q up to 900A"

"The demand for speed control has taken off with the advent of IGBTs and powerful microprocessors. Today, there is no longer any difference between DC and AC. 99% of new installations will be equipped with variable speed AC solutions. In our product range, we have both DC and static frequency inverters. Characteristics of a static frequency inverter: OPEN LOOP CONTROL - Single and three-phase power supply between 200 and 480V - Digital inverter - Solution only in 1 or 2Q - Possible braking via chopper and resistor - Power between 0,37kW and 22kW - IP20 protection - Modular drive - We have a stock up to 22kW in single and three phase CLOSED LOOP REGULATION - Single and three-phase power supply between 200 and 500V -Digital dimmer -Solution only in 1 or 2Q -Braking possible via chopper and resistor -Power between 1,3kW and 900kW -IP00/IP20/IP54 protection -Modular drive We have a stock up to 160kW in three-phase 400V"

"IP23 ventilated open motors (ODP) are an ideal solution for our customers who want compact and smaller motors than IP55 motors. In general, these motors have one less frame size. They are mainly used in clean environments (e.g. manufacturing of plastic bottles for soft drinks, cold compressors for food freezing, ...) STANDARD OPEN VENTILATED MOTORS (OUR CODE: MOV) - Three-phase motors with cast iron housing - IP23 protection - Insulation class F - Heating class B - Legs molded in the casing - Stored in 230/400V - 400/690V - Operating in 50/60hz - Cooling IC01 - Other special voltages or insulation class H on request - Stored speed : 3000 rpm or 1500 rpm or 1000 rpm - Efficiency IE3/IE4 (tomorrow IE5) - Form B3-B5-V1-B35-V15 - Standard motors equipped with PTC sensors for all motors - Motors are equipped with an isolated bearing for use with a variable speed drive. The PI will eliminate circulating currents in the rotor. - Provided with two ball bearings

The Platinum Tools RL-M36A is a compact and powerful Cordless Impact Wrench 20 v. This 20V impact wrench delivers 320ft pounds of max torque and max 3200rpm speed, allowing you to tighten or loosen various nuts and bolts easily. Max no-load speed is 2300 rpm for driving large fasteners quickly. Infinitely variable speeds control is possible with the On/Off switch. The further you push the switch, the higher the speed of the impact wrench. Once release the switch, the tool stops immediately, providing more security. Fast Charger&Power Indicator: Rechargeable 20V 4000mAh Li-Ion lithium-ion battery pack allows the tool to work longer. Power Indicator reminds charger in time. Fully charged in only 1 hour with the matched Platinum Tools fast charger. Features: Compact and powerful with 20V Power capability Infinitely variable speeds control Brushless motor to provide a more stable and efficient work experience.

Air assisted flares enable the smokeless combustion of low pressure waste gases. Air (or Gas) assisted flares can be used when no steam is available on site. Air assisted flares use forced draft Air or Gas to create turbulence ensuring that sufficient primary combustion air is supplied to the flame. The amount of air and hence the size of the tip and riser depend on the degree of smokeless operation required and the maximum flow for smokeless operation. Key features Proprietary design to maximize the mixing of waste gas and air streams and to create turbulence in the combustion zone. Variable speed fans, to supply the optimal amount of Air (Gas) Use of wind deflectors if required, to prevent flame impingement Flame holders around the periphery of the flare tip to ensure stable operation. Use of high grade alloys to enhance lifetime of the flare tip. The use of combustion/mixing air to cool the flare tip and thus enhance its lifetime Key advantages Smokeless operation under a wide range of operating conditions Smokeless flaring of high molecular weight gases Air cooling of the flare tip, resulting in longer lifetime and lower operation and maintenance costs Reduced radiant heat for a given capacity Applications Upstream oil & gas sector Chemical and petrochemical industries including refineries Tank farms and terminals Pipeline transport LNG and NG terminals and compressor stations

This controller regulates the fan speed of single-phase motors from 1,5 to 10 A via phase angle control a.k.a. Triac technology. The supply voltage of 230 VAC can be turned off via the illuminated ON/OFF switch on the side of the unit. Via de potentiometer located on the front of the controller you can set the desired fan speed. Minimum speed can be adjusted via an internal trimmer and kickstart/softstart by adding/removing a jumper on the PCB of the controller. This controller is typically used to regulate the speed of AC fans or centrifugal pumps in HVAC systems. The regulator is also available with TK monitoring. This function will deactivate the motor in case of overheating. The code for this type of regulator suitable for 1,5 A is ITRS-15-DT.