Pumps- electric - Import export

Electrical connections between motor, control cabinet air dryer and water pump. Specific electric motors : protection degrees, IP23 or IP55. Efficiency class : IE1, IE2, IE3. Different optional voltage and frequencies, standard is 400V/3/50HZ or 60HZ +/- 10%. Other voltage is on request : 380V/3/50Hz or 60Hz, 575V/ 60Hz… Soft starter SIEMENS SIKOSTART. Standard is Star Delta starter, the optional soft starter is integrated in the main electrical control cabinet. The compressor is equipped with an electrical pre-lubrication oil pump for the crankcase. Air-conditioning for electrical control cabinet for inside temperatures exceeding 40 for soft starter & 45°C for standard electrical cabinet. The frequency inverter electrical cabinet is protected against high temperature through a different selection of internal components (powerblock…).

Detecting mechanical faults before they stop production Bearing and Machine Maintenance Industry runs on machinery. Bearings, pumps, electric motors, compressors, presses, gearboxes and much more. All of which can break unexpectedly, causing production to stop. When production stops your organization loses money. Few bearings make it to the end of their engineered lifecycle. This is due to poor workmanship, bad lubrication practices and neglect. Problems can even arise right after installation due poor installment of the machine. No two machines are the same. Across industry, machines operate under different loads, climates and conditions, making their maintenance requirements unpredictable. Many machines are still maintained on calendar based PM’s, while others are run-to-failure. Both strategies are wasteful.

Non-rotating asset components seldom receive the routine surveillance they need Hydraulic systems represent another way industry converts electricity to mechanical energy. A pump, normally powered by an electric motor, moves hydraulic fluid through a system. The system is typically made up of a reservoir to hold the hydraulic fluid, high pressure lines to carry the fluid, control valves that ensure the fluid is sent where needed, relief valves for safety, and cylinders to produce mechanical energy. The pump and motor receive attention while the balance of the system is run-to-failure. Ultrasound testing could change this lackadaisical approach; especially considering its versatility, ease of use, and applicability to most hydraulic defects. External and Internal Leaks External leaks can often be found by visual inspection. Some external leaks, like a ruptured hose or fitting, are easy to spot. Simply follow the trail of spilled oil. Others are not so obvious.

The Topstart (Bio)diesel & Oil is an electrical preheating system with forced circulationmade to warm up the (bio)diesel or oil of the engine. It is universal, reliable, easy-to-install and maintenance-free. The system has also following advantages: fuel savings, decreasing pollution, reduced engine wear, no more difficult cold starts. (Bio)diesel & Oil preheater with circulation pump Heavy machined aluminium body 100% recyclable Very compact product with integrated circulating pump for quick and homogeneous preheating Integrated powerful circulating pump saving electricity andimproving the life cycle of engine components Heating element with top-quality shielding and low specific power, increasing its life-cycle Control thermostat with high cutout power for an optimized life cycle Safety thermostat with manual re-set option to protect the heating element if (bio)diesel or oil levels in the circuit are low or if the control thermostat fails High waterproofness Easy replacem

The FlowStart is an electric coolant engine heater for all types of water-cooled engines. It is a system universal, reliable, easy to install and maintenance free. The FlowStart are suitable for all industrial applications either stationary (generator sets) or mobile (heavy-duty vehicle). The engine heater can be put into service a few hours before starting the engine or it can work in standby, in order to keep the engine permanently at the required temperature. This ensures an easy full power start whatever the ambient temperature and avoids cold start mechanical damages. The system has also following advantages: fuel savings, decreasing pollution, reduced engine wear, no more difficult cold starts. Download the technical sheet Advantages: Heavy aluminium injected body 100% recyclable Very compact product with integrated circulating pump for quick and homogeneous preheating Integrated circulating pump saving electricity and improving the life cycle of engine components Low watt den

An indirect dry cooling system is characterized by the use of a condenser and air-cooled heat exchangers.The cooling system consists of the following main components :condenser (surface or spray type),cooling water circulating pumps and recovery turbines, if applicable,heat exchanger deltas including louvers,natural draft cooling tower,piping and valves,water storage tanks and transfer pumps,electrical equipment,instrumentation and control,accessories such as cleaning system, nitrogen blanketing system,The warm water from the condenser is delivered to the natural draft cooling tower by the cooling water circulating pumps and an underground piping network. After the cooling in the heat exchangers, the cold water returns to the condenser.