Electric pumps - Import export

Electrical connections between motor, control cabinet air dryer and water pump. Specific electric motors : protection degrees, IP23 or IP55. Efficiency class : IE1, IE2, IE3. Different optional voltage and frequencies, standard is 400V/3/50HZ or 60HZ +/- 10%. Other voltage is on request : 380V/3/50Hz or 60Hz, 575V/ 60Hz… Soft starter SIEMENS SIKOSTART. Standard is Star Delta starter, the optional soft starter is integrated in the main electrical control cabinet. The compressor is equipped with an electrical pre-lubrication oil pump for the crankcase. Air-conditioning for electrical control cabinet for inside temperatures exceeding 40 for soft starter & 45°C for standard electrical cabinet. The frequency inverter electrical cabinet is protected against high temperature through a different selection of internal components (powerblock…).

Evaporative closed loop cooling towers : For temperatures above 32°C. Cooling capacities are selected to suit the local site wet bulb temperature, up to 30°C ( Wet Bulb ) to provide the most efficient cooling system. The tower and the water pump are controlled by the compressor’s electrical cabinet. Option : two speeds fan motor for winter and summer, antifreeze protections, tracing. Radiator cooling systems. Selected for maximum ambient temperatures up to 32°C, other selections accepting temporary heat peaks up to 36°C and 40°C during some hours per day. These specific versions are equipped with an automatic spray system with thermostatic control The radiator fans and the water pump are controlled by the compressor’s electrical cabinet. The water pump. is mounted on the compressor’s base plate. The cooling system, its functions (automatic spray system for radiators and antifreeze protections for cooling towers) and the water circulating pump are thermostatically monitored by...

Non-rotating asset components seldom receive the routine surveillance they need Hydraulic systems represent another way industry converts electricity to mechanical energy. A pump, normally powered by an electric motor, moves hydraulic fluid through a system. The system is typically made up of a reservoir to hold the hydraulic fluid, high pressure lines to carry the fluid, control valves that ensure the fluid is sent where needed, relief valves for safety, and cylinders to produce mechanical energy. The pump and motor receive attention while the balance of the system is run-to-failure. Ultrasound testing could change this lackadaisical approach; especially considering its versatility, ease of use, and applicability to most hydraulic defects. External and Internal Leaks External leaks can often be found by visual inspection. Some external leaks, like a ruptured hose or fitting, are easy to spot. Simply follow the trail of spilled oil. Others are not so obvious.

Detecting mechanical faults before they stop production Bearing and Machine Maintenance Industry runs on machinery. Bearings, pumps, electric motors, compressors, presses, gearboxes and much more. All of which can break unexpectedly, causing production to stop. When production stops your organization loses money. Few bearings make it to the end of their engineered lifecycle. This is due to poor workmanship, bad lubrication practices and neglect. Problems can even arise right after installation due poor installment of the machine. No two machines are the same. Across industry, machines operate under different loads, climates and conditions, making their maintenance requirements unpredictable. Many machines are still maintained on calendar based PM’s, while others are run-to-failure. Both strategies are wasteful.

The Topstart (Bio)diesel & Oil is an electrical preheating system with forced circulationmade to warm up the (bio)diesel or oil of the engine. It is universal, reliable, easy-to-install and maintenance-free. The system has also following advantages: fuel savings, decreasing pollution, reduced engine wear, no more difficult cold starts. (Bio)diesel & Oil preheater with circulation pump Heavy machined aluminium body 100% recyclable Very compact product with integrated circulating pump for quick and homogeneous preheating Integrated powerful circulating pump saving electricity andimproving the life cycle of engine components Heating element with top-quality shielding and low specific power, increasing its life-cycle Control thermostat with high cutout power for an optimized life cycle Safety thermostat with manual re-set option to protect the heating element if (bio)diesel or oil levels in the circuit are low or if the control thermostat fails High waterproofness Easy replacem

Capacities from 10.000 L to 24.000L. Aluminium tank (various shapes available). light-weight construction with self-supporting tank. Lowered centre of gravity and dished ends front and back. Construction according the latest ADR regulations class 3 fuel transport. Tank made in aluminium 5182 according DIN standard. Tank is divided in 2 to 5 compartments. Electric driven pump, powered by a Li-ion battery pack for silent operation in domestic areas.

An indirect dry cooling system is characterized by the use of a condenser and air-cooled heat exchangers.The cooling system consists of the following main components :condenser (surface or spray type),cooling water circulating pumps and recovery turbines, if applicable,heat exchanger deltas including louvers,natural draft cooling tower,piping and valves,water storage tanks and transfer pumps,electrical equipment,instrumentation and control,accessories such as cleaning system, nitrogen blanketing system,The warm water from the condenser is delivered to the natural draft cooling tower by the cooling water circulating pumps and an underground piping network. After the cooling in the heat exchangers, the cold water returns to the condenser.