Battery screwdriver - Import export

BD 400 is the universal portable electric lift for raising heavy loads safely. Thanks to its unique construction, lifting loads as close as possible to a wall is also possible It is the lifting device suitable for all construction sites or workshops Thanks to its very small footprint and low weight, it can be easily transported for immediate use. Mast with aluminum anti-twist rails Only 2 elements: the elevator and the lifting accessory Immediate use on site, activated in a few seconds without tools 230 V single-phase electric motor with speed variator Possible use in the event of a power outage using the crank provided (or battery-powered screwdriver) Integrated torque limiter, cuts off lifting in case of overload Easy transport on site thanks to transport wheels Stabilizer with adjustable length wheels By design, the feet are placed in front of or behind the mast (for facade work)

CM 520 - Portable electric lift, load capacity: 140 kg up to 3 m 130 kg at 4 m 90 kg at 4.9 m Low weight portable device - only 38 kg Immediate use on site Put into action without any tools Only 2 elements: the mast and the plate With 4 individually adjustable feet Use on stairs or sloping ground Special foot kinematics for working close to the wall (UPTER system) 230 V single-phase electric motor Variable speed at will Integrated torque limiter Manual use possible in the event of a power outage using the supplied crank or screwdriver on batteries

The 2200PTP Series Wireless Power Tools are designed to work with the Global 400 and Global 400mp controller systems. These wireless tools are designed for industrial assembly use. The tool is completely dependent on the Global 400/400mp for directions and torque results reporting. Details on learning and programming the tool through the Global 400/400mp controllers may be found in the controller manual. Models 2200PTP-18: 3-18 Nm / 50-100 RPM 2200PTP-24: 6-24 Nm / 50-600 RPM Key Highlights Report torque/angle values with the results Kits come with side handle

The 2100PTP Series Wireless Power Tools are designed to work with the Global 400 and Global 400mp controller systems. These wireless tools are designed for industrial assembly use. The tool is completely dependent on the Global 400/400mp for directions and torque results reporting. Details on learning and programming the tool through the Global 400/400mp controllers may be found in the controller manual. Model 2100PTP-12: 3-12 Nm / 700-100 RPM Key Highlights Adjustable clutch sets torque limit Report OK/NOK results Kits come with an adjustment tool Double hit detection

Stable ground anchoring is required to ensure the approximately 120-metre substructure is positioned quickly and securely. Our unique, patent-pending earth anchor enables the rail system to be installed simply and without great effort. The in-built laser in the solarfold and specially-produced measuring tape allow you to mark and drill holes for the earth anchor very quickly. The anchor is then lowered onto the ground and screwed down with the battery-powered screwdriver. The earth anchors can be used for a comprehensive range of terrains.

Replacement battery for AS5 battery screwdriver Technical Data: - 3,6 Volt - 1,5 Ah - Lithium-Ion battery

The SSF 10 is a keyless quality drill chuck.Ideal for battery screwdrivers as our AS 5. ► Tension range 1 mm – 10mm ► with ¼“ (6,3mm) - Hexagonal bit ► Length 100 mm ► Diameter 42 mm ► Made of impact resistant plastic ► Tailored to battery screwdriver AS 5 and AS4 with Iso-cap

Insulated socket wrench long - Light using battery screwdriver AS 5 or Bit holder for all counter heights. - The immerson depth of the Bits in the tool is designed to wrench the battery screwdriver and the Bit holder. - Total length of the key 168 mm. - Color code yellow - Maximum torque 12 Nm

Insulated socket wrench long - Light using battery screwdriver AS 5 or Bit hoder for all counter heights. - The immersion depth of the Bits in the tool is designed to wrench the battery screwdriver AS 5 and the Bit holder. - Total length of the key 168 mm. - Color code black - Maximum torque 16 Nm

Insulated socket wrench short - Light using battery screwdriver AS 5 or Bit holder for all counter heights -The immersion depth of the Bits in the tool is designed to wrench the battery screwdrivers AS5 and the bit holder - Total length of the key 70 mm - Color code red - Maximum torque 14 Nm

Insulated socket wrench short - Light using battery screwdriver AS 5 or Bit holder for all counter heights -The immersion depth of the Bits in the tool is designed to wrench the battery screwdriver AS 5 and the bit holder /> - Total length of the key 70 mm - Color code black - Maximum torque1 6 Nm

Charger for the AS5 battery screwdriver - Charger for the new lithium-ion battery of the AS5 (3,6V 1,5 Ah) -The old nickel-cadmium batteries of the AS4 can be loaded with it (3,6V 1,2 Ah)

For exact Centering head screws. • Suitable for Bit-pick-up and Battery Screwdriver • In AuS-design • Centering sleeve replaceable • Individual design to customer with small quantities possilbe. Technical Data • Wear-resistent POM • ¼“ (6,3mm)-BIT-Hexagon • 4,0x0,8 for screw heads Ø 4,5 mm • 5,5x0,8 for screw heads Ø 6 mm • 5,5x1,0 for screw heads Ø 8 mm- For precise centering head screws - suitable for Bit-pick-up und Battery screwdriver - In AuS-design - Centring sleeve replaceable - Individual design to customer with small quantities possible .

Insulated socket wrenche long - Light using battery screwdriver AS 5 or Bit holder for all counter heigths. - The immerson depth of the Bits in the tool is designed to wrench the battery.Die Eintauchtiefe des Bits im Werkzeug ist auf den Akkuschrauber AS 5 sowie auf den Bithalter abgestimmt. - Gesamtlänge des Schlüssels 168 mm. - Kennfarbe rot - Maximal 14 Nm Drehmoment

Insulated socket wrench short - Light using battery screwdriver AS 5 or Bit holder for all counter heights - The immersion depth of the Bits in the tool is designed to wrench the battery screwholder and the bit holder - Total lenght of the key 70 mm - Color code yellow - Maximum torque 12 Nm

Insulated screwdriver Bit 0,8 x 4,0 mm - 113 mm long, so sees the mechanic where he screwed with the battery screwdriver! - Electrically isolated – from the top to the recording! so the voltage stays where it belongs there - into the part and not the tool! - Color code (a color for each screw type; Size by different color gradations seen) – This is the first grip is the right tool at hand!

Insulated screwdriver Bit 1,0 x 5,5 mm - 113 mm long, so sees the mechanic where he screwed with the battery screwdriver! - Electrically isolated‐ From the top to the recording! This is because the voltage where it belongs -into the part and not the tool ! - Color code (a color for each screw type; Size by different color gradations seen) – it is the first grip is the right tool at hand!

Insulated screwdriver Bit PH 1 - 113 mm long, so sees the mechanic where he screwed with the battery screwdriver! - Electrically isolated – from the top to accommodate! So the voltage where it belongs becauset - into the part and not the tool! - color code (a color for each screw type; Size by different color gradations visible) – so is the first grip the right tools at hand!

Insulated screwdriver Bit PH 2 - 113 mm long, so sees the mechanic where he screwed with the battery screwdriver ! - Electrically isolated– from the top to accommodate! So the voltage stays where it belongs because - into the part and not the tool! - color code (for each screw type a color ; Size by diffeerent color gradations visible ) – This is the first grip the right tools at hand!

Insulated screwdriver Bit PZ 1 - 113 mm long, so sees the mechanic where he screwed with the battery screwdriver! - Electrically isolated – from the top to accommodate! So the voltage stays where it belongs - into the part and not in the tool! - Color code (for each screw type one color; Size by different color gradations visible) – so is the first grip the right tools at hand.!

Insulated screwdriver Bit PZ 2 - 113 mm long, so sees the mechanic where he screwed with the battery screwdrivers! - Electrically isolated – from the top to accommodate! So the voltage stays where it belongs there-into the part and not the tool! - color code (for each screwdriver type a color; Size by different color gradations seen ) – This is the first grip is the right tool at hand!

The resilient guide sleeve FFH-M stainless, wear resistant steel for work not performend under voltage ! - For precise centering head screws - Suitable for Bit-pick-up and Battery screwdriver - Centering sleeve replaceable Technial Data: ► wear resistant, stainless steel X 6 Cr 13 ► mit ¼“ (6,3mm) – Hexagon Bit ► Available in size 5,5 x 0,8 x 6,0 for screw heads up to Ø 6,0 mm ► Centering available single ► With the AuS-versions 5,5 x 0,8 x 6,0 und 5,5 x 1,0 x 8,0 combined

Thread standard: Metric, ISO DIN 13 Type: Machine bit tap Form D, for through and blind holes Application: General use Material of product: HSSG Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 900 N/mm2 Standard: Factory standard Tolerance: ISO2/6H Bit taps have been designed for thread cutting using battery-powered screwdriver drills and electric hand drills with right-hand and left-hand rotation. But they are also suitable for thread cutting by hand or in a stationary drilling machine. Your battery-powered screwdriver drill should have a minimum power of 7.5 Volts. Take care that the tool and the axis of the hole are exactly aligned and use a suitable cutting oil. For thread cutting we recommend using battery-powered screwdriver drills and electric hand drills with lowest rotaionsettings (0 - 450 RPM) and maximum torque settings.

Thread standard: Metric, ISO DIN 13 Type: Combined machine bit tap (core hole drilling and thread tapping) for through holes Application: Combined (core hole drilling and thread tapping) Material of product: HSSG Surface treatment: no For materials: Materials of medium mechanical strength, non ferrous metals and thermoplastics Tensile strength up to: 600 N/mm2 Standard: Factory standard Tolerance: ISO2/6H Combined Bit taps have been designed for drilling, tapping and deburring in one operation using battery-powered screwdriver drills and electric hand drills with right-hand and left-hand rotation, but they are also suitable for thread cutting in a stationary drilling machine. It is possible with this tool to produce through threads up to a maximum threaded depth of 1 x D. They are especially usefull for mounting an dsmall batch production. Take care that the tool and the axis of the hole are exactly aligned and use a suitable cutting oil.