Alloy work - Import export

Introducing the esteemed Master Alloy ALTiB, a distinguished solution meticulously crafted to elevate the realm of grain refinement. This exceptional alloy has been ingeniously designed to enhance both performance and surface quality, setting new standards in the industry. Master Alloy ALTiB finds its unparalleled utility in a myriad of applications, most notably in aluminum castings, aluminum profiles, and aluminum cables. Its remarkable properties ensure a refined grain structure, resulting in superior mechanical properties and enhanced overall performance. With utmost precision, this esteemed alloy works diligently to refine the grains, bestowing a level of excellence that surpasses conventional alternatives. Its profound impact on the end product is evident, as it imparts an impeccable surface quality, elevating the aesthetic appeal and durability of the aluminum components.

SS 305 is an austenitic Chromium-Nickel stainless steel with excellent corrosion resistance, and is suitable for very severe cold forming operations. A high nickel content reduces the work hardening rate so that it can be formed into electronic components and remain non-magnetic. The alloy is readily formable and work hardens slowly.It has good resistance to nitric and sulfuric acid solutions although it will not resist halogen acids. The alloy can be satisfactorily welded, brazed, and soldered. Available Sizes: SS 305 is available from Hamilton Precision Metals as strip product in thicknesses from 0.0005” to 0.050” (0.0127 mm to 1.27 mm) in widths up to 12.0” (304.8 mm). It is also available in foil as thin as 0.000200” (0.00508 mm) in widths of 4.0” (101.6 mm) maximum. The material conforms to ASTM A240, QQS-766, and UNS S30500.

Ti Grade 9 is a near alpha, alpha-beta alloy, sometimes referred to as “half-6-4.” It offers 20 to 50% higher tensile strength than the commercially pure titanium at room and elevated temperatures. It is much more amenable to cold working than Ti 6AI/4V alloy and can be cold worked 75 to 85% to result in moderately high strength and good ductility The alloy can be formed from the annealed temper. Severe forming may be aided by an intermediate stress relief. Stress relieving may be appropriate after severe cold forming to remove residual stresses. Weldability and corrosion resistance is very similar to commercially pure titanium. Welding should be performed with inert gas shielded arc or spot welding.Welding with active gases, coatings, or fluxes must be avoided to prevent embrittlement.

L-605™ is a nonmagnetic cobalt-based chromium-tungstennickel alloy that has excellent corrosion and oxidation resistance, and high strength at both room and elevated temperatures. Through work hardening, high strength levels can be obtained. L-605™ has a minimal heat treatment response, but can be used in the cold worked and aged condition. Applications include medical implant devices, springs, valves, and engine components for the aerospace industry. As a result of its high tungsten content, L-605TM is radiopaque, which is beneficial for implant medical devices, such as stents. Because of the alloy’s high work hardening rate, only minimal reductions can be taken before solution annealing will be required. L-605TM is very resistant to oxidation and scaling at elevated temperatures, and is nonmagnetic in all conditions. L-605™ is produced by vacuum induction melting followed by electroslag remelting (VIM-ESR), and as such, has a low nonmetallic inclusion level.

Ti 3AI/2.5V (Titanium Grade 9) alloy is a near alpha, alpha-beta alloy, sometimes referred to as “half-6-4.” It offers 20 to 50% higher tensile strength than the commercially pure titanium at room and elevated temperatures. It is much more amenable to cold working than Ti 6AI/4V alloy and can be cold worked 75 to 85% to result in moderately high strength and good ductility. Furthermore, it is weldable as the commercially pure grades and has excellent resistance to torsion and corrosion.Ti 6Al/4V is significantly stronger than commercially pure titanium while having the same stiffness and thermal properties excluding thermal conductivity, which is about 60% lower in Grade 5 Ti than in CP Ti. Amongst its many advantages, it is heat treatable. Please note that we have a minimum order value of £10,000.

HPM® 625 is a nickel-chromium-molybdenum alloy with niobium which is well suited for a wide range of severe corrosive environments. The alloy composition provides a product which performs well at elevated temperatures up to 1800°F. The strength can be increased by cold working. The alloy is readily formed in the annealed temper, and can be joined by the standard welding and brazing processes. Available Sizes: HPM® 625 is available from Hamilton Precision Metals as strip product in thicknesses from 0.001” to 0.025” (0.0254 mm to 0.635 mm) in widths up to 12.0” (304.8 mm). The material conforms to ASTM B443, AMS 5599 and UNS N06625.** **Hamilton Precision Metals can also supply product to AMS 5879 (UNS N06626) for demanding fatigue applications, which incorporates double melting, and restrictive limits for Carbon and Nitrogen.

Havar® is a heat treatable Cobalt base alloy that provides very high strength. The alloy has excellent corrosion resistance and is non-magnetic. Applications have included metal diaphragms for aerospace sensors, metal diaphragms for burst discs, power springs, gap spacers in magnetic heads, and target foils in nuclear physics. Forming cold rolled Havar requires large radius (90° Bend – 8 X thickness) prior to age hardening. The joining can be accomplished using both welding and soldering techniques.The ultimate endurance life is achieved by heat treating the alloy at 1000°F after 80% cold work. The alloy will retain 75% of room temperature strength up to 950°F (Figure 1). Available Sizes: Havar® is available from Hamilton Precision Metals as strip product in thicknesses from 0.0005” to 0.025” (0.0127 mm to 0.635 mm) and widths to 7.5” (190.5 mm). A foil product is available in thicknesses down to 0.000060” and widths of 4.0” (101.6 mm). The material corresponds to UNS R30004.

Pure A100 allows for non-contamination when working with high tempuratures 356-T6 Alloy perfect for heavy work, more durable Abbott aluminium hammers are the perfect alternative to lead, brass and plastic tipped hammers. Single piece cast construction gives maximum solidity and guarantees safety because head cannot separate from handle. The hammers are non-sparking, non-marring and have excellent vibration dampening characteristics that allow the handle to absorb impact forces instead of your hand.

The TER-GP190-WS comes with an internal PYTHON engine and a hardware watchdog. It easily replaces PLC. The TER-GP190-WS uses 2G/GSM/GPRS networks for connection. The device has three LED lights: Error or ERR light which is red, Application or APP light which is yellow and Status or STA light which is green. The RS232 9-pole SUB-D connector is on the same side of the device. TER-GP190-WS has a SMA/M antenna connector and an internal SIM holder. It has 4 digital 0-28 VDC inputs which are fully decoupled (optional 2 digital and 32 sensors via I2C). In case of an emergency or blackout, TER-GP190-WS has an optional battery which can last up to 4 hours. The case is made up of aluminium alloy (IP20) and the working temperature range is from -25°C to +70°C.

Overlapped pairs of aluminium oxide flaps and X-weight backing. Only the flat version is available. Main features and benefits: The aluminium oxide abrasive is particularly suitable for applications requiring low and medium operating pressure and even for low-power cornering grinders. The paired flap arrangement provides better ventilation and improves scrap/waste escape. Wide abrasive surface, constant wear, continuous exposure of new grit, high and even cutting performance. Recommended applications: Deburring, removing welding seams and spots, removing scale, rust and oxidation of any kind. Work surfaces: Alloyed and unalloyed steel, aluminium, nonferrous metals and alloys, structural steel, plastic, paint, varnish, filler Minimum order quantity for articles not included in 1036 program: 200 pcs/diameter 115 - 80 pcs/diameter 178

Particularly robust nylon backing. Overlapped pairs of aluminium oxide flaps and X-weight backing. Only the flat version is available. Main features and benefits: The aluminium oxide abrasive is particularly suitable for applications requiring low and medium operating pressure and even for low-power cornering grinders. The paired flap arrangement provides better ventilation and improves scrap/waste escape. Wide abrasive surface, constant wear, continuous exposure of new grit, high and even cutting performance. Always use the backing pad for the 165mm-diameter disc. Recommended applications: Grinding, removing welding seams and spots, removing scale, rust and oxidation of any kind. Work surfaces: Alloyed and unalloyed steel, aluminium, nonferrous metals and alloys, structural steel, plastic, paint, varnish, filler. Minimum order quantity for articles not included in 1036 program: 200 pcs/diameter 110 - 80 pcs/diameter 165

Individually arranged aluminium oxide flaps and X-weight backing. Only the flat version is available. Main features and benefits: The aluminium oxide abrasive is particularly suitable for applications requiring low and medium operating pressure and even for low-power cornering grinders. Wide abrasive surface, constant wear, continuous exposure of new grit, high and even cutting performance. Recommended applications: Deburring, removing welding seams and spots, removing scale, rust and oxidation of any kind. Work surfaces: Alloyed and unalloyed steel, aluminium, nonferrous metals and alloys, structural steel, plastic, paint, varnish, filler Minimum order quantity for articles not included in 1036 program: 200 pcs/diameter 115 - 80 pcs/diameter 178

Individually arranged aluminium oxide flaps and X-weight fibreglass backing. Both flat and conical versions are available. Main features and benefits: The aluminium oxide abrasive is particularly suitable for applications requiring low and medium operating pressure and even for low-power cornering grinders. Wide abrasive surface, constant wear, continuous exposure of new grit, high and even cutting performance. The fibreglass backing does not damage or foul the surface worked in the case of accidental contact. It provides good strength while maintaining a satisfactory degree of flexibility. Recommended applications: Deburring, removing welding seams and spots, removing scale, rust and oxidation of any kind. Work surfaces: Alloyed and unalloyed steel, aluminium, nonferrous metals and alloys, structural steel, plastic, paint, varnish, filler Minimum order quantity for articles not included in 1036 program: 200 pcs/diameter 115 160 pcs/diameter 127 80 pcs/diameter 178

Individually arranged aluminium oxide flaps and X-weight fibreglass backing. Both flat and conical versions are available. Main features and benefits: The aluminium oxide abrasive is particularly suitable for applications requiring low and medium operating pressure and even for low-power cornering grinders. Wide abrasive surface, constant wear, continuous exposure of new grit, high and even cutting performance. The fibreglass backing does not damage or foul the surface worked in the case of accidental contact. It provides good strength while maintaining a satisfactory degree of flexibility. Recommended applications: Deburring, removing welding seams and spots, removing scale, rust and oxidation of any kind. Work surfaces: Alloyed and unalloyed steel, aluminium, nonferrous metals and alloys, structural steel, plastic, paint, varnish, filler Minimum order quantity for articles not included in 1036 program: 200 pcs/diameter 115 160 pcs/diameter 127 80 pcs/diameter 178

Aluminium oxide flaps and X-Flex weight backing ¼-20 UNC shaft thread. Main features and benefits: Being quick to change, our RG flap wheels on threaded shaft can be ideally used in robotized applications or intensive production lines. In addition to this, it is extremely easy to switch over to a new grit on the same tool by manually unscrewing the wheel. Recommended applications: Finishing small parts, moulds, alloy wheels, robotized applications. Work surfaces: Stainless steel, standard steel, alloyed steel, aluminium, titanium, nonferrous materials and alloys, plastic materials, glass fibre, rubber, marble.