Results for
NORELEM FRANCE
France
2-phase high-torque stepper motor in NEMA 17, NEMA 23 and NEMA 34 sizes with flat-milled shaft (D-shaft). 1.8ׄ° increment angle (full increment) with integrated positioning control. Note: Stepper motor with integrated positioning control. It forms a convenient unit consisting of stepper motor and intelligent controller. Reference travel is possible on a block with reduced electric current without proximity switch. Integrated rotational monitoring. Smooth running through dynamic switching of increment trip. Actuation via single I/O interface, 31 position configurations and call-ups. Control unit can be parametrised quickly and conveniently with the software. The software and manual for programming the positioning control are available as free download. When selecting a suitable motor, using just the retaining torque is not enough, as the motor’s torque decreases with the speed. It is therefore essential to select the correct motor according to the torque curve.
Request for a quoteNORELEM FRANCE
France
Bearing block and carriage aluminium alloy. Guide column and threaded spindle stainless steel. Plain bearing for guide columns and spindle nut highquality special plastic. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Stainless steel hardened and ground. Threaded spindle with ball bearing. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Positioning stages for motorised adjustment and positioning tasks. The plain bearings and spindle nuts are suitable for dry running, however lubrication with a grease for plastic plain bearings is recommended. The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).
Request for a quoteNORELEM FRANCE
France
Base and rotary table aluminium alloy. Hollow shaft stainless steel. Preloaded worm gear steel. Claw coupling aluminium with polyurethane coupling spider. Version Aluminium alloy anodised. Note for ordering The unit is supplied with the position of cable outlet or control unit as shown in the drawing. Note Rotary positioning stages for motorised adjustment and positioning tasks. The preloaded worm gear runs virtually playfree. The bearing of the worm shaft offers maximum radial rotational accuracy. Cables can be routed through the large bore in the hollow shaft. The adjustable positioning ring is used to determine the rotational reference point to the position of the assembled part. Proximity switches can be mounted with the optionally available sensor holder (21094). The suitable programming software and interface cable for the stepper motor with positioning control are available as accessories (2500015).
Request for a quoteCIC - KLAUS CZERWONKA
Germany
Pneumatic cylinders according to the norm, standard or special design, completely configured ready for installation and pre-assembled with add-on parts, bearing elements, compressed air connections, position sensors or control valves according to customer specifications.
Request for a quoteEC PLAZA
South Korea
Universal Testing Machine is a representative test equipment for physical properties. It is capable of measuring load, strength, elongation of products or materials such as rubber, film, plastic, metal, etc. - Frame Load Capacity (Max.) : 5kN - Main Load Cell : 5kN - Load Range : 50 (kgf) ◀(Up to 4-step conversion) - Column Type : Single Column - Load Accurancy : Less than ±0.5% - Crosshead Speed Range : 0.01 ~ 500mm/min - Load Resolution : 1/50,000 - Machine Controller : Touch Type Servo Controller(Position Control Type) - Test Category : Tensile, Tear, Peel, Compression, Bending, Repeat, etc. - Dimensions : 478× 650× 1375(H), 82kg - Main Power : AC 220V 2P, 50/60 - It is single column model that can be tested under 5kN. - UNITEST M1 is widely used for testing materials such as films, rubber, fibers, medical devices, biomaterial, and wires etc. - The main feature of the UNITEST M1 is that it requires a small footprint
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
EC PLAZA
South Korea
1. Foam Filled Fender Foam-filled fenders are constructed with an energy-absorbing foam core and a tough outer skin of filament-reinforced polyurea elastomer. 2. Fender Skin The elastomer used in the fender skin is polyurea. The skin is reinforced by filament winding wrap in a helical and hoop direction, which is controlled by an automatic winding system with load cell sensors at each filament. Our four-axis filament winding system, also used to build spacecraft fuel tanks, takes control and positions each filament for maximum strength and even finish. The polyurea shows far superior physical properties to those of the rubber. The durable and resilient polyurea skin also offers the best resistance to salt water and ultraviolet light. 3. Various colors Standard color shall be made of Dark red, gray and black. But customers can request yellow etc.
Request for a quoteTOK EUROPE GMBH
Germany
SR2 provides controlled motion to adjust the height at any position. Through its inverse interrupting mechanism, this breakthrough technique conducts driving from the input shaft to the output shaft and locks the input in place even if the drive is stopped. Thanks to this new mechanism, you can easily lift heavy objects and lock them precisely into position. This new control motion is perfect for applications such as adjustable tables, handicap sinks, and more. [Benefits] ・ No power supply ・ Easy operation ・ Ready to install ・ Competitive price
Request for a quoteGLOBAL INDUSTRIAL SEWING MACHINES
Netherlands
3200 HFD 2000 (only delivered completely mounted and installed) – Semi automatic lockstitch curtain hook attaching machine with fully automatic curtain hook feeding device. • Versatile Global semi automatic high speed curtain hook attaching machine, for hook-sizes of 55 mm, 75 mm, 95 mm. • Quick load hook container, stores up to 100 hooks. • Fully automatic curtain hook feeding device with automatic adjustment of the hook-height between 5 and 50 mm in steps of 5 mm. • Sensor controlled positioning of the hook exactly under the needle. • Special tack program for fixation of the pleats ( separate operation). • Capacity up to 1500 hooks a day. 3200 HFD 2000 (only delivered completely mounted and installed) – Semi automatic lockstitch curtain hook attaching machine with fully automatic curtain hook feeding device. • Versatile Global semi automatic high speed curtain hook attaching machine, for hook-sizes of 55 mm, 75 mm, 95 mm. • Quick load hook container, stores up to 100 hooks. •...
Request for a quoteResults for
Position controller - Import exportNumber of results
9 ProductsCountries
Company type