Guides - Import export

Electro zincplated. Tracks inductively hardened and ground. Note for ordering Fastening screws are supplied. Note Compact Cprofile guide rails with internal hardened tracks. The system runs with low noise even under heavy loads. There is play between the screw and the fastening hole to allow the rail to be aligned during installation. To achieve the desired running properties there must always be a film of lubricant between track and roller, this also provides corrosion protection for the ground tracks. On request Lengths up to max. 4080 mm.

Carriage body zinc. Plastic bearing material iglidur® J. Rails anodised aluminium. Version Body chromed. Guide rail natural colour anodised. Note Miniature slide guides are maintenancefree and corrosion resistant. Very high speeds and accelerations are possible due to the low weight. Applicable temperature max. 80 °C. Miniature slide guides are insensitive to dust and are ideal for dry running. ** length L2 = 30 mm and * L = 1000 mm included L2 and L only available in full mm.

Guide units for attaching cylinders according to ISO 6432 and VDMA 15552. For moving heavy loads with high speed and positioning accuracy.

The compact, guided cylinder CC is a linear drive with a lot of power and minimal dimensions. Generously dimensioned guide rods on plain bearings or ball bearings open up a wide range of application options in variable positioning with and without sensor queries.

The compact, guided cylinder CC is a linear drive with a lot of power and minimal dimensions. Generously dimensioned guide rods on plain bearings or ball bearings open up a wide range of application options in variable positioning with and without sensor queries.

Profile guide rails can be screwed on from above. The profile guide rails are available in four sizes and one or more carriages can be assembled on them. 4row versions with round arch profile. The tracks of the profile guide rails are set below an angle of 45° and thus can carry loads from all directions. The profile guide rails correspond to the market standard and can replace linear guides of the same design by other manufacturers. On request Lengths up to a max. 3960 mm.

These precision slideways with roller bearings are used in machine and fixture construction, metrology, optical instruments and precision mechanics. The scale division on the micrometer dial is 0.02 mm. The stated permissible load values (F) are designed for a service life of 1 million travel cycles. The torque values apply only to centred slides. An additional centring hole is located at holes D2 and D3 on the top of the slide. Other connecting elements can be precisely mounted on the slide in combination with our centring rings 20240. F = permissible loading for dynamic and static loads. TI E/E1 = number of fastening holes E/E1/M inside. TA E/E1 = number of fastening holes E/E1/M outside. TI E4 = number of fastening holes E4/D1 inside. TA E2 = number of fastening holes E2/D1 outside.

These precision dovetail slides find use in e.g. machine and fixture construction, metrology, optical instruments and fine mechanics. The stated permissible load rating (F) is for static loads. The torque values only apply for centred carriages. TI = number of fastening holes E1/E2/MI inside. TA = number of fastening holes E/E1/MA outside. TM = number of centring holes D1 inside. TN = number of centring holes D1 outside. Advantages An additional centring hole is located at all tapped holes. Other connecting elements can be precisely mounted on the slide in combination with our centring rings 20240. Quick and retrofit combination in the X, Y and Z axes.

These precise slideways are used in e.g. machine, fixture and metrology equipment construction as well as in the optical and precision engineering industries. The central set screw M1 can be replaced by a clamping lever 06460. The stated permissible load values (F) are designed for dynamic loads with a service life of 1 million travel cycles. For static loads, 10 times the table value F is permitted. The torque values apply only to centred slides. An additional centring hole is located at holes D2 and D3 on the top of the slide. Other connecting elements can be precisely mounted on the slide in combination with our centring rings 20240. TI E = number of fastening holes E/M inside. TA E = number of fastening holes E/M outside. TI E1 = number of fastening holes E1/D1 inside. TA E1 = number of fastening holes E1/D1 outside.

Race body steel. Wipers plastic/felt. Longitudinal sealing lips rubber. Rollers steel 1.3505. Note Roller carriage with lifetimelubrication roller bearings and wipers which lubricate the system when moving. By simply moving the centre cam roller, the roller carriage can be adjusted so that it is free of play or has the desired pretension in the rail. High travel speeds up to 7 m/s and extremely quiet (faster and quieter than systems that use recirculating balls). The wipers are fitted with an oilsoaked felt. This felt is in constant contact with the track to ensure perfect lubrication. The felts can be recharged using an oil pump through the lubrication points on the front. On request Roller carriages with 4 or 5 rollers.

Aluminium outer ring and inner ring. Iglidur® J plastic slide elements. Stainless steel A2 screws. Version Anodised outer ring and inner ring. Note Aluminium plain bearings with replaceable, high performance material glide elements for rotary stages. Such a combination of materials guarantees absolutely lubricant and maintenancefree running. Simple assembly. High wear resistance. For high loads, high rigidity.

Extruded section, aluminium EN AW6060. Version Hard anodised aluminium, 50 µm. Hardness 500 HV. Note The aluminium guide rail has good thermal conductivity and importantly heats only at continuously very high speeds. ** lengths L2 = 20 mm * and L = 500 mm included L2 and L only available in full mm.

Sliding carriage Base structure in extruded section, aluminium EN AW6060. Sliding elements Maintenance free plain bearing iglidur® J. Version Eloxalcoated E6/EV1. Black thermoplastic Note With a low rate of inerita, high accelerations and short term extreme speeds up to 30 m/s are possible. DryLin® T linear glide guides are resistant to dirt and corrosion and are adjustable, maintenancefree and quiet. Application temperature max. 80 °C. As no lubricants are used they are recommended for use in food, medical, and clean room technologies. Manual clamping was developed for simple functions. Polymer under constant pressure has a tendency to creep which causes a decrease in clamping force over time (up to 70%), which means that no safetyrelevant parts should be clamped. Suitable guide rails see 21200. Drawing reference 1) manual clamping

Selflubricating. Hardness 190220 HB. Note The guide bushes are radially and axially applicable. The bearing elements are maintenancefree and wearresistant. The graphite inserts provide lifelong lubrication. Preferably for travel speeds < 0.5 m/s. (Additional lubrication is recommended for extreme loading with a higher travel speeds). Temperature range Temporary temperature peaks up to ca. 200°C. Tolerances The bore for the bearings should correspond to ISO tolerance H7. The tolerance h6 to h7 is recommended for the shaft.

Steel 1.1213. Stainless steel 1.4034. Stainless steel 1.4112. Version Steel, ground. Steel, ground and hardchromed, chrome coating 5 10 µm. Stainless steel, ground. The precision steel shafts are generally inductively surface hardened. Note The surface value obtained during the inductive hardening process guarantees high surface wear resistance. Suitable for shaft supports 21565. On request Lengths up to a max. 4000 mm. Accessory Shaft supports 21565. Drawing reference 1) chamfered

Shaft support with bore for easy and secure clamping and fastening the guide shafts. Precision guide shafts 21595. Fastening screws 07160 or 07161.

The readytoinstall compact linear housing consists of extruded aluminium housing, installed linear ball bearing 2151102 and doublesided seal. Recommended shaft tolerance h6. Load rating according to specification of the linear ball bearing. With lubrication hole M8x1. Accessory Precision guide shafts 21595. Fastening screws 07160.

Housing steel. Cage plastic. Balls steel. Note The linear ball bearings correspond to series 3 of ISO 10285. With doublesided seal. The linear ball bearings have a plastic cage which results in quiet and outstanding running properties. With flange for direct mounting on the housing. Linear ball bearings with doublesided seal should be greased before installation. The specified load ratings apply with the use of hardened and ground shafts. Precision guide shafts 21595. Fastening screws 07160.

Housing steel. Clamping lever plastic. Threaded spindle grade 12.9. Version Housing nickelplated. Clamping lever, spindle black oxidised. Note Manually operated clamping elements for static clamping tasks. Manual clamping process using the freely adjustable clamping lever. The floating clamp ensure symmetrical application of force onto the rail. Up to 50,000 static clamping cycles (B10d value). In general, a friction connection is created between the clamping element and the the linear guide on the open faces of the profile guide rail so that the ball guide tracks are not damaged. The retaining force is tested on an oil smeared profile guide rail. An adapter plate, dependent on the type of carriage used, is required for height adjustment.

Body carbon steel. Balls roller bearing steel. Diverters plastic. Standard guide carriage with recirculating ball guidance precision N not preloaded (Z0). With doublesided end seal. 4row versions with round arch profile. The profile guide rail tracks are arranged at 45° and can accept loads from all directions. High dynamic values v = 5 m/s. Applicable temperature in continuous use max. 80 °C. On request Various precision and preload classes. Drawing reference 1) ground ref. edge

Exceptionally wearresistant Dimensionally stable even at high temperatures Electrically insulating Frequency neutral

Body, extruded aluminium section. Bearing housing and slide, aluminium. Profile guide rail and guide carriage, steel. Toothed belt, polyurethane with steel cord reinforcement. Version Body natural colour anodised Bearing housing and slide, black anodised. Tracks of the profile guide rail, inductively hardened and ground. Note Compact and flexible linear actuators with toothed belt drive. The body consists of a selfsupporting aluminium extruded section with integrated profile guide rail. This rail system is able to absorb highest forces from all directions, is lowwear, and is optimised for moving large masses. Slots are located on the outer sides of the aluminium profile, ensuring easy, reliable assembly and enabling accessories mounted. Proximity switches can be positioned and fastened in the upper Tslot. The aluminium profile is fully compatible with our standard I series profiles.

Body and flange plate EN AW5754. Guide shafts steel Version Body, hardcoated Flange plates, anodised. Guide shaft, hardened. Note Maintenancefree pneumatic linear modules with two precision steel shafts and ball guide bushing with wipers. Double acting cylinder drive. All fastening threads have threaded inserts. The as accessory available shock absorbers and proximity switches can be integrated (no protruding edges). Positive fit construction for hundred per cent reproducibility. Combinations in all sizes and stroke variants are feasible without adapter plates. Repeat accuracies of ±0.01 mm are possible. Specified loads apply by centred carriages. On request Available with locking cartridge as stroke deviation safeguard. Accessory See table for shock absorber, proximitiy switch and plug connector.

As of 1st October 2023, the European Union mandates that businesses from third countries exporting select products, including Hydrogen, Cement, Urea, Ammonia, Fertilizers, Iron, Steel, and Aluminum, provide comprehensive carbon footprint data. With Tevolution Ltd's expert services, seamlessly navigate this intricate mandate and stay compliant. Understand the nuances of the new EU regulations. Navigate the boundaries set by the EU with clarity and confidence. Comprehensive assessment to ensure your data's accuracy and compliance. Detailed classification code reviews for each product. Thorough examination of your business processes. Align your methods to the EU's stringent standards. Ensure complete compliance, reducing risks of non-adherence penalties. Achieve peace of mind with expert-backed data accuracy. Stay ahead in the market by showcasing commitment to sustainability and transparency.

SCHOCK has been a successful innovator and manufacturer of ball guides for linear motion technology for decades. SCHOCK ball guides are known for their precision, high load capacities, and long lifespan. Key features of SCHOCK ball guides include: Excellent running properties High operational reliability Long lifespan without maintenance Custom connection options Based on individual customer requirements, we develop and manufacture ball guides as runner guides, partial extension, full extension, or over-extension. In collaborative project planning with our customers, we define the product requirements for the ball guides. Our customers benefit from a wide selection of rail profiles, mounting systems, comfort features, and high-quality surface finishes, such as SCHOCK powder coating. We supply powder-coated ball guides in any desired RAL color, offering you unique design possibilities.