The electronic reverse polarity controllers are used to turn the magnetic clamping plates on and off and to regulate the holding force in several stages through the affiliated manual operating device.
With the D50 controllers, up to 100 poles with the pole size 50x50mm or 50 poles with the pole size 75x75mm can be switched. Furthermore, the D100 controller is needed.
The single-channel devices D50 and D100 are used to control Magnaslot and Doublemag.
The D50-2 controller is needed to operate the Triplemag magnet modules with additional holding surface.
If multiple magnetic clamping plates are controlled individually, the D100-4 controller must be used. Up to 4 clamping plates can be switched separately here.
Individual requests can be implemented upon customer request.
EPM D50 to 50A:Item No. 13070
EPM D50Flux:Item No. 66847
EPM D50-2 to 50A:Item No. 63863
EPM D100 at 100A:Item No. 52950
EPM D100-4 to 100A:Item No. 58088
Foot switch:Item No. 53832
The uniform radial pole division offers significant advantages compared to magnetic chucks with parallel pole or square pole division in particular wh...
The electropermanent load lifting magnets from the EMPH series are suitable for the lifting and transportation of individual slabs and unprocessed blo...
The ASO 600-ASL edge and contour deburring machine is designed for chamfering small to medium-sized workpieces. The refined machine features, such as ...
Robust and maintenance-free 90° magnetic clamping angle for flat material.
The permanent magnet welding angle is a classic from Assfalg for welding a...
The SMA 40-A series is available in an electrical or compressed-air operated design. The machine is designed for handling steel, aluminum, copper and ...
The SMA 60 is available in an electrical, compressed-air or high-frequency design. The machine is designed for handling steel, aluminum, copper and pl...
The automatic weld-chamfering machines from the ASO 930 series are for stationary and portable use in weld seam preparation. The attachment of large w...
The electropermanent load lifting magnet traverses TBK4 and TBK6 with automatic telescopic arm allow the lifting and transportation of sheets in diffe...
The AR series was specifically designed for workpieces that do not have any level contact surfaces. They are only switched on or off with a short comp...
The manual magnet transporter magnetizes and demagnetizes with the push of a button. Nevertheless, it holds like a permanent magnet. Oily, sharp workp...
The Pivot magnetic welding angle has a holding angle range from 28 to 270 degrees.
The Pivot magnetic welding angle is a universal handyman for small...
The KKF4-SL, a universal chamfering and contour milling machine, has an ER collet chuck. Tools with a shaft diameter from Ø6-12 mm can be clamped. Our...
The EPM M electropermanent load lifting magnets are used where there is a frequent change of workpieces due to the very short switching times. Only a ...
The uniform radial pole division offers significant advantages compared to magnetic chucks with parallel pole or square pole division in particular wh...
The electropermanent load lifting magnets from the EMPH series are suitable for the lifting and transportation of individual slabs and unprocessed blo...
The ASO 600-ASL edge and contour deburring machine is designed for chamfering small to medium-sized workpieces. The refined machine features, such as ...
Robust and maintenance-free 90° magnetic clamping angle for flat material.
The permanent magnet welding angle is a classic from Assfalg for welding a...
The SMA 40-A series is available in an electrical or compressed-air operated design. The machine is designed for handling steel, aluminum, copper and ...
The SMA 60 is available in an electrical, compressed-air or high-frequency design. The machine is designed for handling steel, aluminum, copper and pl...
The automatic weld-chamfering machines from the ASO 930 series are for stationary and portable use in weld seam preparation. The attachment of large w...
The electropermanent load lifting magnet traverses TBK4 and TBK6 with automatic telescopic arm allow the lifting and transportation of sheets in diffe...
The AR series was specifically designed for workpieces that do not have any level contact surfaces. They are only switched on or off with a short comp...
The manual magnet transporter magnetizes and demagnetizes with the push of a button. Nevertheless, it holds like a permanent magnet. Oily, sharp workp...
The Pivot magnetic welding angle has a holding angle range from 28 to 270 degrees.
The Pivot magnetic welding angle is a universal handyman for small...
The KKF4-SL, a universal chamfering and contour milling machine, has an ER collet chuck. Tools with a shaft diameter from Ø6-12 mm can be clamped. Our...
The EPM M electropermanent load lifting magnets are used where there is a frequent change of workpieces due to the very short switching times. Only a ...