piston installation

...The sliding gate control valve type 8044 in short design with piston actuator and integrated positioner is due to its compact design universally applicable for neutral and aggressive media in the chemical industry, process engineering and plant design. Due to the direct and backlashfree installation of the positioner on that piston actuator, these valves have no exposed moving parts and are...

... glides on an air cushion with minimal wear and works against two air cushions. As a result, the piston vibrator type VP has very low air consumption and a low noise level, which is only about 45 to 60 dBA. The piston vibrator type VP has a very compact installation mass and can be used in all positions. For long and uninterrupted operation, we recommend installing an air filter before the vibrator. The piston vibrator type VP is used in the following industries: conveyor technology, dosing, weighing and screening technology, packaging industry, chemicals, pharmaceuticals,...

... by ACE. This enables direct installation as end position damping in pneumatic cylinders at 5 to 7 bar or applications where deceleration needs to take placed close to the pivot point. They are maintenance-free, have an integrated positive stop and are mountable in any position. The option of a side load adapter allows impact angles of up to 25°. Thanks to their robust design and their durability...

... piston rod cylinders are manufactured in accordance with various ISO standards and are available in single or double-acting versions. They are suitable for filtered, non-lubricated, or lubricated compressed air.

...Pressol pneumatic Oil pump installation set for 200/220L drum model 19235600 To pump Engine, transmission, hydraulic oil. Ideal for direct connection to pipeline systems up to 70 m Can be easily combined with several hose reels Suitable for oil up to SAE 90 Installation set consisting of: Oil pump 3:1 model 19235 Compressed air hose 2 m DN10 with quick couplings Euro profile Oil drain hose 2 m DN13 with 1/2G bi.bu Ball valve 1/2 Filter Pressure Regulator with Oil Mister 20218950...

... Monitoring of torque and rotation angle during tightening and loosening — Hollow piston hydraulic cylinder Lifting stroke 12 mm Installation force up to 58 kN — Quick change system For fast handling and maintenance-free operation Reduced tooling costs through the use of DIN studs as an extraction tool (optional)...

... simultaneously When different diameters should be covered by one part Installation recommendations pistons installation recommendations for housings Installation recommendations for housings Dimensions [mm] dS (h-tolerant) [mm] dG (h-tolerant) [mm] bg [mm] Nominal diameters dS = d1 dG = d2 bG = b1 +0,2 Installation recommendations for pistons Dimensions [mm] dG (h-tolerant) [mm] dH (h-tolerant) [mm] bg [mm] Nominal diameters dG = d1 dH = d2 bG = b1 +0,2 b1: Desired length Inner and outer Ø (d1 and d2) made using standard plain bearings* M for metric PRfor piston ring iglidur® desired material...

...Designed for installation in hydraulic cylinders and valves. Pressure-tight up to 400 bar Measuring ranges: 2 - 180 mm Design: Piston Maximum linearity: ±0.3 %, optional ±0.2 % / ±0.1 % Analog output: AC, 0...10 V, ±10 V, 0...5 V, ±5 V, 4...20 mA, 0...20 mA Protection class: IP67, optional IP68 Operating pressure: max. 400 bar...

...Double-acting pneumatic cylinder according to DIN ISO 21287. Piston rod with threading or thread, position detection via proximity sensor, and bilateral elastic damping. Thanks to their compact dimensions, compact cylinders are particularly suitable for use in confined installation spaces. Reference: 12001 Cylinder tube: aluminum Cover: injected aluminum Piston rod: Stainless steel 1.4301 (from...

...Standard sizes available for all common installation spaces in various designs. PTFE-bronze, PTFE-carbon, and PTFE-graphite are the most commonly used materials in conjunction with NBR elastomers. Other sizes and materials available upon request.

...we custom produce a wide variety of machine parts and hardware components according customer's drawing. Such as tube coupling, hose coupling, shaft,Axis,pipe joint parts,hose connectors & transition connectors,copper machined tube, flange,bushing, Sleeve,knighthead,pedestal,Piston Rod,insert long pin, Dowel Pin,Drive Pin & Rod,ball head bolt,long rod machined parts,long thread tube parts...

...The SGH10 wire-actuated encoder measures the absolute direct cylinder stroke in a hydraulic cylinder. The new measuring system eliminates costly boring of the piston. As a result, integration costs are reduced compared to other measuring systems and a possible weakening of the piston is avoided effectively. Thanks to its unique lateral installation, the SGH10L can also be used in almost...

... perfo sleeves) etc. The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust etc. The following accessories are provided for easy use of the cartridges Syntech Profix: - Gun for resins in a cartridge with rack-and-pinion piston. - Perfo sleeves (only for hollow masonry and perforated blocks) - Spout mixer for two-compartment cartridges (mixing tip...

...-standard compressor, the pipe jacking machines from the ROVER-TECHNIK product range dynamically drive steel protective pipes through the ground. After the jacking process is completed, the soil core is expelled from the pipe string using water and compressed air. Compelling arguments that speak for themselves: • No more costly production interruptions • No destruction of valuable surface land • More cost-effective than open construction methods • Horizontal and vertical pipe installation, any angle is possible • Rocky ground is not a problem Convincing...

...Install our LUXE birch springboard and cleat system to the face panel of a MWBS bed for the most comfortable wallbed experience available. This upgrade works with on wallbeds using the SBLM, SBLM-A, and Cloud piston mechanisms, across all bed sizes. Installation is easy and the results are dramatic.

...-safe). - Use in safety-related systems according to EN 61508 - Use in Zone 2 and Zone 22 - Wide torque range - Solid, corrosion-resistant aluminum housing - Maintenance-free - Operation in any installation position Due to the honed surface of the cylinder bore, these actuators achieve a long service life. The control pressure ranges from 2.5 bar to 8 bar, allowing for a torque range from 5 Nm to 10,000 Nm. The anodized aluminum housing and the powder-coated covers of the pneumatic swivel actuators ensure good...

... shoulder on the piston rod. There are connections with screw-in holes for pipe fittings to BSPP ISO 1179-2 as well as vent holes for a free installation position. With the exception of the piston rod, all surfaces are protected against corrosion with a black primer. On request alternative surface treatments are possible. The surface of the piston rod is hard chromed, ground and polished. The cylinders...

...Double vice with useful passage 250 mm (front width 260 mm) Clamping force: 14000 kg Complete with unscrewing piston Vice sectors with height 105 mm Ready for installation Producer:Project Template:Morsa 250 mm Condition:New...

... series are offered for guiding the piston rods of ISO 21287 cylinders. . Type 34*EC is the most compact version, where a rigid connection of the piston rod is directly screwed into the front plate. This model is therefore limited to cylinders with a maximum stroke of 50 mm. . Type 34*EF features a floating rod coupling between the piston rod and the front plate. This model allows for the installation of cylinders with a longer stroke (max. 100 mm recommended).

... pair of clamping jaws, 1 recovery bowl, 1 MSU assembly key and 1 MSZ, maintenance booklet and spare parts list Features • Hydraulic head made of aluminum, cylinder surface with wear-resistant treatment • Pneumatic cylinder made of cast aluminum • Thanks to the hardened and chrome-plated steel piston, the device operates effortlessly and is wear-resistant • Long service life, due to compact wear-resistant seals with high scraping effect • Quick-release valve for fast return and high productivity • Adjustable hydraulic head at 360° Material: Aluminum, Steel...

...Concentrated linear force with a nominal pressure of 250 bar and a test pressure of 375 bar, piston diameter of up to 320 mm, available in differential or equal stroke cylinder design.

...— brackets are equipped with cross slots to guarantee an ideal adjustment of the installation set — Length compensation fittings to find the optimum position of the water meter — Screw connections with roughened external thread for even more tightness QUICKTURN piston valves — easy operation by ergonomically shaped handles — fast operation with just a few turns from "open" to "closed...

...for cold drinking water up to 30°C resistant to aggressive water Continuous flow Q3 2.5-4 m³/h (MID) for horizontal or vertical installation Detection of minimal flow rates, Starting value < 2 l/h Modular counter, retrofittable with remote reading modules...

STAF has been offering TURNKEY SOLUTIONS in INDUSTRIAL REFRIGERATION since 1996. Our service scope includes ENGINEERING AND CONSULTING, THERMAL INSULATION, REFRIGERATION PRODUCTION, REFRIGERATION ACCESSORIES, ELECTRICITY, and CONTROL during project execution, as well as MAINTENANCE afterwards. Our products are primarily intended to equip: - REFRIGERATED WAREHOUSES - COLD ROOMS - AGRO-FOOD AND PHAR...

... be supplied upon request at any time. Technical data: Piston mm 15 Rod mm 10 Swing angle +- 2° 0,90,60,45 Operating pressure min. bar 30 Operating pressure max. bar 250 Pulling force max. kN 2.45 Swing stroke mm 11 Clamping stroke mm 6 Total stroke mm 17 Effective piston area (cm²) Clamping 0.98 Releasing 1.77 Oil requirement per stroke (cm³) Clamping 1.37 Releasing 3 Permissible flow rate (cm³/s) Clamping 6 Releasing 6...

... the discharge side to reduce sound by minimizing pulsations. Therefore, only vertical installation is possible. Speed range from 1450 to 4800 rpm. Oil splash lubrication with oil sight glasses on both sides. Shaft seals Coupled with neutral chambers open to the atmosphere, the transport chamber and its carbon ring seal have proven themselves for decades. Drive shaft with ring seal...

... adjustment during the foundation. Available in telescopic design for limited installation depth or underlying basement, with piston distances of 1,300 mm, 1,700 mm, or 2,300 mm depending on the application. Fixed maintenance-free crossbeam that guarantees 100% synchronization of both pistons. Since your electricity bill is also important, we want to draw your attention to the fact that the motor power of most models is only 2 kW, whereas other brands are usually forced to work with 3 kW motors. Classic H-lift: drive-over lifting bridge and standard UI.

... and speed to your vehicle. - Original Quality: Designed with WABCO's assurance, this COMPLETE COMPRESSOR SINGLE CYLINDER reaches the pinnacle of durability and reliability. - Efficient Design: Enhances your fuel efficiency, providing an eco-friendly driving experience. - Easy Installation: Its special design allows for quick and hassle-free installation. Choose the COMPLETE COMPRESSOR SINGLE CYLINDER now to give your vehicle a burst of energy. Enjoy the thrill of performance and make every journey unforgettable!

...Aerator compressors primarily used for the ventilation of small biological wastewater treatment plants. High performance and quiet operation. Technical Specifications: - Air flow: 80 l/min - Continuous pressure: 0.15 bar - Power consumption: 86 W - Voltage frequency: 230V / 50 Hz - Noise level: 38 dBa - Hose connection: Ø 18 mm - Dimensions (L x W x H): 307 x 190 x 208 - Weight: 5.3 Kg Advantages: - Low energy consumption - Quiet - Easy installation - Estimated lifespan: 8 to 12 years with proper use...

...Jet - Self-Priming Surface Pump - PUMPS AND LIFTING STATIONS Model: JET In stock: 5 Products Liquid temperature: from 0 °C to + 35 °C. Maximum suction depth: 8 m. Maximum ambient temperature: + 40 °C. Maximum operating pressure: 8 bars. Installation: to be installed in a horizontal position.