moving media

...The preeflow flowplus16 is a media-resistant, dead-space-free miniature pressure sensor in a compact design - for moving fluids. With the dual "Luer-Lock" (male/female), it is suitable for all common dosing systems that operate with this type of thread. The sensor generates a standardized, compatible, linearized, and temperature-compensated output signal. Existing dosing systems can be easily...

...The sliding gate control valve type 8043 in long design with piston actuator and integrated positioner is due to its compact design universally applicable for neutral and aggressive media in the chemical industry, process engineering and plant construction. Due to the direct and backlashfree installation of the positioner on that piston actuator, these valves have no exposed moving parts and are...

...FMCW Radar Level Measurement Device for Moving and Corrosive Liquids The OPTIWAVE 7400 is a 2-wire 24 GHz FMCW radar level measurement device for liquids in harsh environments, such as tanks containing corrosive media and agitators. It is specifically designed for continuous, non-contact level measurement under extreme conditions, as found in the chemical, petrochemical, or oil and gas industries...

...The Drum pump F 426 is ideal for mixing and/or pumping inhomogeneous media. You can keep media moving that tend to segregate, even during pumping. With the outlet closed, e.g. via a hand nozzle, the F 426 can be temporarily operated as pure mixing pump. By turning the adjusting lever, the pump can be easily adjusted to "mixing" or "pumping". The pump is easy to dismantle for rapid cleaning. The...

...Flow sensors without evaluation electronics for liquid media in Ex areas - EGE flow sensors for explosion-prone environments enable space-saving flow detection on-site and convenient adjustment of the threshold value at the separate evaluation electronics, e.g., in a control cabinet. The measurement is carried out without mechanically moving parts using a thermal measuring element. The current...

... When quiet, maintenance-free operation is required When rust-proof property is required At -10°C to +60°C constant temperature At accelerations over 10 m/s² Energy supply system for all media, not only electrical Also suitable for outdoor use (with reduced load data) Your benefit from LBT FLIZZ® Guaranteed service life Cost-effective compared with conventional energy supply systems Cable...

... construction guarantees good long-term stability and high reliability, while being resistant to aggressive media – which can be measured in liquid or gaseous states. The structure of the sensors includes no mechanical moving parts, which is why they show so little sensitivity to impact and vibration. The pressure sensors can be configured with options to suit the user. Standard types are...

... between temperature and voltage corresponds to the characteristic curve for the Pt 1000 and is thus nearly linear. The assignment between temperature and output voltage is nearly freely selectable, the lesser temperature corresponding to the lesser output voltage. The sensor‘s lowest possible output voltage is 0.1 V and its greatest is 10 V. The output is overload-proof and short-circuit-proof. The sensor has no mechanical moving parts and so is not susceptible to vibration and soiling.

... compatibility The low start and running moment, especially at low temperatures, enables a high efficiency The good wear protection increases the life time of the part and makes sure a reliable functionFor best results clean the lubrication point with OKS 2610/OKS 2611 Universal Cleaner. Remove the corrosion protection media before initial filling. Fill the bearings in a way that all the functional...

...Compact and easy-to-maintain construction as well as low weight allows an easy handling. Speed is sensitively and continuously adjustable, smooth start, insensitive to vapor, dust and smoke. Compressed air keeps all moving parts clean. Insensitive to heat, suitable for high ambient temperatures. Compressed air expanding in the air engine cools the agitator drive. The pneumatic agitators are explosion proof and overload proof until standstill. Type test certificate for explosive zone 0.

...In addition to tubular heaters for applications in still or moving air, our portfolio is complemented by fluid tubular heaters. The tubular heaters are tailored individually according to your specifications. Tubular heaters consist of a high-quality insulating material with an embedded heating coil, surrounded by a stainless steel jacket. Tubular heaters are characterized by their universal...

... with you to develop a tailored digital strategy, perfectly suited to your needs and focused on the most relevant channels for you: LinkedIn social media, website, web optimization (SEO), content strategy, videos...

... management, archiving, and the preservation of backup media. The outsourcing management service consists of three phases: - analysis of issues and preparation of the project - taking charge of the archive - consultation of the archive conducted by container, by practice, or by individual document...

...Effectively communicate your vision, values, and the very essence of your business through our captivating corporate videos. Our dedicated team works closely with you to create videos that reflect your brand's identity, showcase your teams, and engage your audience. Whether for an internal presentation, a marketing campaign, or social media distribution, our corporate videos help you stand out and establish authentic connections with your audience. Trust us with your story and let us tell it through moving images.

... moving in the axial direction. By capturing the entire amount of mixing material, an intensive mixing process is achieved with short residence times, until the finished mixture exits the mixer through the discharge opening. Application-specific design of the mixing tools and adjustments to the mixing plant's rotational speed allow for flexible use. The optional installation of knife heads in the...

...Typical Features: • Wide range of viscosities • Gentle, low-shear pumping • Maximum suction capability • Dry running safe • Reversible • Long service life and easy maintenance The hose squeeze pumps are designed for robust use. They are suitable for low to high viscosity, viscous, sensitive, shear-sensitive, aggressive, abrasive, pure, or solid-containing media. The absence of moving parts, such...

...Highly accurate for both small and large flow rates. Pressure and temperature compensated through the thermal mass flow principle. Quick and easy installation via a standard ½" ball valve. No moving parts, thus low maintenance. Negligibly low pressure loss due to minimal blockage of the diameter.

... and steam phases. Reliable measurement in case of moving surface and foam or in changing medias. Measuring Principle:Guided radar Characteristic / Application:Premium device high pressure/ high temperature; Rod probe, Rope probe, Coaxial Probe; Integrated dat Interface measurement:Clean interfaces liquid/ liquid54321; Simultaneous measurement of interface and overall level Supply / Communication...

...The aquasant® probe technology operates without moving parts, unlike conventional measurement systems, and is independent of the dielectric constant, density, and organic attachments. The standardized rod probes are customized according to process conditions and the media used, and they are maintenance-free. Materialization according to requirements (e.g., stainless steel, Hastelloy®, full PTFE...

...Content that reaches the target audience is more important than ever today. We create high-quality content for all formats, channels, and media. From photography to moving images. Product photography for your sales optimization. Creation of employee photos for image-building recruitment. Corporate presentation via promotional videos. Production of animated explainer videos. Creation of your promotional film. Content concepts for social media content, moving images for your website, product photos, shop images, corporate shots, and an in-house photography studio.

... VDC supply, valve input and pulse output can be connected. The pulse factors are adapted to the magnetic-inductive flow meter, so that the devices can be interchanged easily. Advantages • compact design • direct measurement of mass • measurement of non-conductive media • very short dispensing time down to 250ms • high accuracy / repeatability • no moving parts • easy to clean compared with piston filler • product gentle filling Flexibility • DN 10, 15, 20, 25 • liquid temperature 0°C to 90 °C • different connections available such as: • Tri Clamp acc. DIN 32676 • Sanitary thread acc. DIN 11851...

...The electronic flow monitor VE allows for the monitoring of liquid media to ensure that a specified flow rate is not fallen below. The VE operates based on the calorimetric principle and can also monitor solid-loaded flows, as it does not have any moving parts. It is characterized by a robust design, straightforward operation, and high reliability. With the VE, you receive a safe and cost...

... insertion version from 3/4" to DN 500 — With ATEX certification ATEX II 2G Ex d IIC T4 — With DVGW certification for natural gas (up to 16 bar) — Pressure range up to 50 bar, special version up to 100 bar — Temperature range up to 180 °C — No moving parts, no wear — Sensor tip very robust, easy to clean — Simple installation and removal under pressure via 1/2" ball valve — Housing rotatable...

...and similar containers or tanks with a 3/4" or 2" internal thread. - Precision measurement of fill levels in shallow containers - Measurements in containers with overpressure or underpressure - Measurements in liquids prone to foaming - Measurements in outgassing liquids - Measurements on moving surfaces C2: standardized 2-wire 4-20mA output. Housing: PE, PP Seal: PTFE...

... one of the sorting bins is full. System requirements for the control PC: Operating system Windows XP, 7 or 8 .NET Framework 4.5 or higher 2 RS232 or USB Ports Dimensions / weight W x D x H: 390 x 470 x 460mm, 25kg Media Power supply: 230 V, 50 Hz or 120 V, 60 Hz. Other voltages / frequencies on request Pressurised air: dry and clean air, 0.6 MPa (6 bar) elmor Green Design Our label for: high energy efficiency longevity no standby power loss most components may be recycled production without solvents, ROHS conformity...

... solutions. Examples include: chemicals, polymers, mineral oils, and many other liquid media. Key features: • Application-specific pump design through a wide range of materials and sealing options as well as 13/12 sizes • Robust construction for high operational reliability • Long service life • Low maintenance due to few moving parts and maintenance-friendly design • Available with FDA and EN1935/2004 materials for the food industry • ATEX...

...The CS 20 is a pneumatically controlled spraying device for high and low viscosity (including abrasive) media. The spray jet is generated solely by the material pressure, which forces the material through a nozzle (the same nozzle used in high-pressure spraying; airless method). The spraying quantity is influenced by the nozzle cross-section, material pressure, viscosity, and opening time. A minimum spraying time of 0.2 seconds is possible. Few moving parts ensure high reliability.

...Piston and rod seals offer significant advantages in sealing static or moving pistons and rods, either as spring-supported profile rings or as memory seals. Spring-supported profile rings with excellent dry running properties, low wear, and low friction. No stick-slip effect - even at low sliding speeds. High shape stability and very high chemical as well as thermal resistance. Medium: for liquid media.

...Filtration of aqueous media with automatic and continuous backwash filters Flow rate up to 250 m³/h (based on clean water) Nominal diameters DN150 (optionally DN100, 125, 200) Programmable control Welded, one-piece housing made of 1.4571 Backwashing without operational interruption No moving parts within the system Short flushing times Compact, vertical design Filter fineness nominally starting...

...The 7G injectors are pumps designed for transporting and mixing various media. The basic principle is simple: a gaseous medium serves as the drive, escaping through a drive nozzle at high pressure and great speed. In the process, the medium from the surroundings is drawn in or sucked in, allowing it to be fed into the subsequent production process. Due to their design, injectors operate without moving parts, making them low-wear and robust. Drive: gaseous medium...