gap sealing Germany

... bitumen, chocolate, paints, oils, etc. Options: Flange cover for upward removal of the filter insert Heating jacket Magnetic coupling for hermetic sealing Operation up to 16 bar Operation up to 200°C...

... just a few components and has a large, gap-free sealing range of 3.5 mm to 23 mm. The material of the sealing insert is FDA-compliant and the temperature application range of this cable gland is -55 °C to 180 °C. Outer parts:Stainless steel 1.4404 Inner parts:stainless steel 1.4305 Connection thread:Metric connection thread according to EN 60423 Type of protection:IP 68 up to 15 bar, IP 69 Material of sealing elements:Silicone HTS Temperature range (min./max.):–55 °C/+180 °C...

... to the flexibility of the material, large gaps between the media and casing pipes are not necessary, but a minimum annular gap of 40 mm is required. The material fold accommodates the pipe movements and thus provides the necessary flexibility. The pressure tightness is achieved by pressing the stainless steel bands over the sealing segment. Before backfilling, the sleeve must be covered with a stretch cushion (provided by the construction site).

... Putty 3765 must not only be elastic but also plastic, so that it can penetrate into every gap when pressed and remain there to complete the seal. Technically, this is only achievable by combining two base materials with the same chemical structure but different molecular weights. These two components fulfill the above requirement for sufficient penetration depth while maintaining the stability of...

...coolants, saltwater, as well as weak alkalis and acids. Profile: ELRING CURIL T Base: Synthetic resin Character: Cured, permanently plastic Color: Green Viscosity: Paste-like / approx. 30000 mPa*s Maximum sealing gap: 0.1 mm Processing time: 5-10 minutes Electrical conductivity: Insulating Operating temperature: -40 °C to +250 °C (short-term up to...

...HEUTE+COMP manufactures sealing elements and support rings for O-rings from high-performance materials according to your specifications. PTFE support rings prevent the O-ring from extruding into the sealing gap under high pressures, which can lead to damage. Pure PTFE is only conditionally suitable for sealing applications due to its material-related cold flow and high wear. Therefore, a variety...

... combination boxes. Now, a box height of 180 millimeters and flush ceiling installation are also possible. This makes the previously required 50-millimeter overhang from the ceiling unnecessary. Installed without tools or drilling, simply seal the remaining gap with the included foam panels or Soudafoam GUN B1. The Pacifyre® CB combination boxes are also suitable for hassle-free retrofitting and easy re-filling.

...Precision tools with a cutting gap of only 0.02 mm ensure an optimal cutting profile. By manufacturing hot sealing tools for sealing shielding plates onto the corresponding plastic parts, we provide our customers with the entire range of production equipment—from forming/punching to the hot sealing process—all from a single source.

... applications. Here we can only show the tip of the iceberg. Challenge us! Nominal sizes::DN 65 - DN 250 Length::EBRO factory standard Top flange::EN ISO 5211 Flange connection::Pipe system - clamping ring groove Max. operating pressure::max. 3 bar Temperature range::-10°C to +130°C, (optional 220°C) (depending on pressure, medium, and type of drive) Housing::Aluminum Disc::1.4301 Shaft::1.4401; 1.4571 or alternatively as specified Gap between housing/disc::0.1 mm to 0.5 mm, depending on application...

... a reliable alternative to conventional dynamic shaft seals. Different dimensions and types of magnets allow for the achievement of various torque levels. To avoid eddy current losses, the use of a PEEK or ceramic gap ring is recommended. In addition to standard models of magnetic couplings, these are also available as face couplings or hysteresis couplings.

... significantly reduced. The sealing effect is achieved through 4 spring lamellas, which are mounted in a fan-like arrangement in the carrier profile. Quality Features of Separator Plate Seals Type MMT Like all products from Möller MetallDichtungen GmbH, the separator plate seals of type MMT meet our high quality standards. Regular testing in our laboratory and production-related quality assurance...

...The 1+ fitting consists of only two parts: the body and the opposing screw. The clamping ring is integrated into the opposing screw. The threading and the socket are integrated inside the body of the fitting. They can no longer be damaged and are protected against external influences. Other advantages: The fitting is completely leak-proof "when tightened by hand"; no tools are required, and assembly times are significantly reduced. Additionally, the opposing screw can also be tightened with a flat wrench to achieve a gap-free connection to the body of the fitting. Pressure: PN16...

...To achieve this accuracy and optimal efficiency, the internal sealing of the pressure chambers is adjusted around the circumference of the gears and the height of the gears through appropriate gap dimensions, depending on the medium to be conveyed, the pressure, and the corresponding viscosity. Depending on the requirements, special hard coatings on the components provide a wide range of...

... - Compact design with low space requirement - Compact design with integrated control cabinet - Glue gap or tuck-in gap closure is possible - Modular machine design for maximum flexibility for future adaptations of products, packaging or functions - Few moving parts resulting in minimized sealing and maintenance costs Output::up to 150 Pieces/min Format change time::max. 40 minutesFormat range: Format range::max. 200 mm x 200 mm x 200 mm Basic measurements approx. (LxWxH)::7500 mm x 2900 mm x 2000mm...