axial flow Germany

...Axial expansion joints compensate assembly tolerances and thermal longitudinal expansion in the direction of the tube axis. Depending on the design, they can be impinged with pressure internally and externally. Using a guide sleeve protects the metal bellows from abrasive media or flow-induced oscillations. The reaction forces caused by the internal pressure must be absorbed by sufficiently dimensioned anchor points.

...Advantages Fully automatic cleaning process; forced strip off through axial acraper; minimal pressure loss Area of application Special design for high viscosity media Flow rate Various filter sizes and the modular design enable any required flow rate. classification number T89 Filter aid - Filtration degree 50 µm - 5 mm Medium Oil, lacquer, water, chemicals Filter material Slotted tube Cardtridges...

...The TG/MN sleeve can be used where a pressure-tight seal is required and axial and radial movements need to be accommodated. Sealing Segment All sealing segments are embedded in secure sealing pockets, thus providing excellent protection against slipping and cold flow behavior of the sealing material; the precise arrangement of the stainless steel tension bands is also ensured. Material Folds Due...

...Axial Piston Pump AV 10 VSO Available immediately: 28 cc, 45 cc, 71 cc - Adjustable pump with axial piston drive in swash plate design for hydrostatic drives in open circuits - Continuous flow rate adjustment is possible through the adjustment of the swash plate - 2 leakage fluid connections - Good suction behavior - Permissible continuous operating pressure 280 bar - Low noise level - High...

...Form parts can be manufactured with radial or axial knurling. These knurlings are applied during the pressing process or in subsequent machining.

... applications with short piping. The flow rate ranges from 200 to 50,000 m³/h with a maximum pressure difference of 500 Pa. They are available in eight nominal sizes with inlet diameters from 200 to 1000 mm. The housings are standardly made of PPs and optionally available in PVC. These fans are suitable for explosion-prone areas (extraction from ATEX Zone 2). For more information, please visit our website or contact us directly.

...Construction size: DN 630 – DN 2500 Application: Supply and exhaust ventilation up to 55°C continuous temperature or flue gas up to 400°C/120min Volume flow: max. 500,000 m³/h Pressure: max. 3,000 Pa Motor: Frequency range: 50/60Hz, max. 250 kW Surface: Coated steel/stainless steel (V2A 1.4301 / V4A 1.4571) Impeller: reversible / adjustable blade angles at standstill Drive: Direct Accessories: extensive accessories...

...Highflow Elements High Flow - Pleated element with a diameter of 152mm and lengths from 20" to 60" are suitable for high flow rates. Radial or axial pleating.

... used to transmit torque. It can also be transmitted axial forces and bending moments. The shrink connection do not transmit any forces and/or moments between the shafts and hubs, they just provide the necessary forces. They are not in the flow of forces. It is installed by sliding the flanges onto the shaft ends and subsequent tightening of the pressure ring. Thereafter the flanges are connected by bolting. The rigid flange couplings are supplied ready for installation. The clamping is done manually by means of screwing tools. Optionally with a hydraulic clamping tool. To achieve proper...

... bottom of the container, directly beneath the L-wing, a strong shear zone is concentrated. The axial flow evenly distributes the shear vortices generated during bundling throughout the container, better than other radially acting shear stirring elements. In addition to these process engineering advantages, the guide ring reduces the risk of accidents. When used with a stand or clamp stirring device, the L-wing minimizes the risk of damaging the stirring device, the container, or the fittings due to incorrect positioning.

...Our oil reservoir cleaning system M 504 has the capacity of cleaning large oil containers like large tanks and reservoirs, and to store enormous amounts of water and dirt. The M 504 consists of 4 large C-1200 housings and achieves a flow of nearly 300 liter per minute. Due to the large filter elements (1.5 m purely axial flow) this machine is the solution to re-obtain an oil quality in...

...Submersible Lift Pumps The TAA series lift pumps equipped with axial impellers discharge lubricating refrigerants sensitive to foam formation. Impellers: axial Pumped liquids: cutting fluids, emulsions, neat oils Flow rate: up to 440 l/min Height: up to 9 m Fluid: for cooling liquid, cutting and cooling oils Drive: electric Priming: semi-submerged Technology: centrifugal Field: industrial, for machine tools, for the metallurgical industry Other features: single-stage, for cooling, for emulsion, for lifting, for suction, for cutting fluid...

...In a liquid cooler, the warm liquid medium is cooled in the pipes using cooler ambient air. Due to the lower heat transfer on the air side, the surface of the smooth pipe is enlarged by finning. Depending on the flow rate and pressure drop, a single or multi-path design is chosen. Heat dissipation is achieved through quiet axial fans. Features: • Various designs are possible • Due to its...

...The Flowform® screw is a polygonal screw based on TAPTITE 2000®, which makes use of the technology known as "flowhole-forming" in manufacturing processes. Using this technology the Flowform® screw causes the sheet metal to heat, using a combination of axial force and relatively high screwdriver speed . Once the material has been penetrated the polygonal shape of the screw forms a calibrated...

...Suitable for all applications with large air volumes at low pressures. Typical applications include bottle cleaning systems in the beverage industry, laboratory exhaust, and all applications with short piping. Key data: - Flow rate of 200 - 50,000 m³/h with a maximum pressure difference of 500 Pa - 8 nominal sizes available with intake diameters from 200 to 1000 mm - Housing standardly made of PPs material, optionally available in PVC...

For over 130 years, we have been producing industrial radial and axial fans with impeller diameters ranging from 200 to 2500 mm, as well as all components for flow control and sound reduction. Benefit from our experience in building fans for corrosive, abrasive, and toxic media. For your exceptional challenge, we calculate, develop, and produce customized special designs. Our extensive range of...

Manufacturer of axial piston hydraulic motors, hydro-regulating pumps, and flow dividers. With over a century of experience, we provide top-notch solutions in hydraulic technology. The company MW Hydraulik Maschinenwerke Frankfurt GmbH has been active for decades as a manufacturer of axial piston hydraulic motors and hydro-regulating pumps. Our motors are successfully used in machine tools, transfer lines, and other areas due to their high power density and small, compact design.