cylinder of motor Germany

... variant available. Areas of application: Switching speed not critical, suitable for long-term switching states, high flow rate, low susceptibility to particles. Lifespan: 50,000 switching cycles, easy replacement of the actuator, high-quality materials, and reliable sealing. Technical Data: FSA Motorized Ball Valve Set Stainless Steel 304 3/4" 9 - 28V Actuation: Open/Close Switching time: 8...

...For driverless vehicles, the test operation requires additional safety in the form of redundancy for brake activation. Our emergency brake actuator offers a safe option with the highest reliability. As soon as a communication failure occurs, the pneumatic cylinder is activated via a normally closed valve from a monitored pressure reservoir. The brake pedal is thus pressed, and the vehicle is decelerated using ABS braking. The installation takes less than 3 minutes and requires no modifications to the vehicle. It also does not interfere with manual vehicle operation by the driver when installed.

...In the serial arrangement, a vertically aligned linear drive shaft (double-acting linear cylinder) is mounted on the vertically aligned rotary drive shaft (swivel motor), i.e. the piston rod of the cylinder and the output shaft of the swivel motor are mechanically coupled via a movable shaft-hub connection. The pallet holder is lifted by the piston rod, which also serves as a bearing for the...

...With the compact heavy-duty cylinder SLZ 63, RK Rose+Krieger expands its product portfolio with another electric cylinder designed for high pressure and tensile loads of up to 10,000 and 15,000 N respectively. The heavy-duty cylinder SLZ 63 features an ideal installation stroke ratio due to the parallel mounting of the motor. Its maximum stroke length is 1,000 mm, but lengths of up to 1,500 mm...

... seconds, compared to 15 seconds for the HS30290, making it significantly faster. The hydraulic oil is included with your purchase. You will need to fill it yourself after final assembly. However, you will need to procure the motor oil in advance and also fill it after final assembly (approximately 0.6-1.1 liters). We recommend Briggs & Stratton 4-Stroke Engine Oil SAE30 for this purpose...

...SERAC® LH – Modular Design for a Variety of Solutions In addition to the basic versions LH30, LH50, and LH100, all options can be selected in combination: - Anti-rotation device (fully enclosed) - Motor holding brake - Linear measurement system - Various motor encoders Upgrades and modifications can also be carried out by us retroactively.

... thanks to its lightweight design which can hold maximum loads Grab drive: Vertical electrohydraulic drive unit with high-pressure pump Closing and opening movements are controlled through clockwise or counter clockwise rotation of the electric motor (turn control). The electric motor is only switched on whilst the closing and opening movement is being performed. Grab connection bearing: Re-greaseable steel bushing bearing Stable, torsion-resistant design using direct cylinder linkage Material:S355J2+N...

...Its 6mm tool housing, stable design, and piston motor that requires virtually no maintenance make it an essential tool, even for tasks that demand high endurance such as rough cleaning of molds.

... conditions, offer a wide range of applications. Advantages -Extended oil change intervals and thus reduction in operating costs -Excellent soot-carrying capacity reduces abrasive wear in the engine -Best engine cleanliness thanks to low deposits and an optimized detergent system -Year-round savings potential with quick oiling thanks to synthetic base oils with excellent Container size:208 Product number:1508776...

...For milling plastic and aluminum profiles, with a quick-change device for milling sets. Easy handling and perfect results. Even milling feed through a hydro-pneumatic cylinder. Why WEGOMA? • Hydro-pneumatic cylinder for consistent results • Pneumatic double clamping device • Profile stop swivels on both sides up to 60° • Depth stop for four positions • Quick-change device for cutter replacement • With machine stand • With automatic shutdown via motor brake Special accessories • Cooling spray device • Milling spindle additionally available in various diameters • Profile-specific milling sets...

...Avola GAMA 65 V revolving cross cut / rip cut saw Equipment / scope of supply- Cutting heights 90° / 245 mm - 45° / 164 mm - 30° / 113 mm - Machine table with lateral movement approx. 400 mm with pneumatic brake system - Machine hood with lateral PVC protective curtains - pneumatic clamping cylinder left - right - pneumatic cross-cutting operation using two-hand control - electrical saw...

... Monitoring of torque and rotation angle during tightening and loosening — Hollow piston hydraulic cylinder Lifting stroke 12 mm Installation force up to 58 kN — Quick change system For fast handling and maintenance-free operation Reduced tooling costs through the use of DIN studs as an extraction tool (optional)...

... • Extensive range of accessories for every application Rivet diameter (Rm=370 N/mm²): 1-3 mm Rivet force at 6 bar pneumatic: 1.8 kN Spindle stroke: 5-30 mm Operating pressure: 1-6 bar Motor 230/400 V 50 Hz: 0.25 kW Cylinder volume: max. 0.25 l Weight: approx. 48 kg Working range: 1-95 mm Reach: 127 mm Clamping area: 225x175 mm...

...The circle shears in sizes KSE 25 - 100 are all motor-driven. They can process round diameters ranging from 80 mm to 3,200 mm. The maximum sheet thickness can reach 10 mm. They meet the highest standards of industrially manufactured sheet circles through cutting and flanging. The machine is driven either in one, two stages, or continuously; on the upper and lower shaft. The frame adjustment is...

... it is handed over and handled in the same manner as before. The insertion and tensioning of the core is done manually using a clamping mechanism. The core is clamped in a chuck that is axially rotatable in the direction of the wire pull. The core is driven by a chain and a positioning motor, allowing for precise control of the feed. To prevent the wire from slipping during the winding of the first turns, a pneumatic gripper is attached to each of the core clamping jaws.

...With load compensation, smaller motors can be used. This results in lower costs for the motor and reduced energy consumption. Our products are characterized by: • High quality and competitive performance. • Transmission through backlash-free couplings with high torque. • Carriers with ribs for cross-bracing and existing threads at the profile end. • The most comprehensive selection of accessories...

...Micro Cylinder with only 14 mm Cross-section The ultra-compact RCD micro cylinder is a rod type with a length of only 52 to 72 mm and a width of only 12 mm. The motor-driven micro cylinder is designed for applications with low load and power requirements. It can be used for short strokes, press mounting, lifting and lowering and many other applications. The micro linear cylinder with 24 VDC...

...The SpeedPOWER electric cylinders feature a planetary roller screw drive. This design has a significantly higher number of contact points between the spindle and the nut compared to ball screw drives. This allows for greater performance in the same size. A lifespan up to 15 times longer and higher speeds are additional advantages over ball screw drives. Electric cylinders with integrated motor and servo controller The Tritex series is a "ready-to-connect" system with an attached servo controller. The effort required for commissioning is minimal.

...Application The Hunger SHM is designed for precision honing of cylinder liners with bore diameter from 150 to 640 mm. Features • Air powered honing. Powerfull air motor for rotary motion of honing head, air hoist for stroke motion and, as an unique feature, air cylinders for stone feeding. • Superior control. Manual buttons are provided for fine adjusting setting of honing head RPM, stroking rate...

... bearings separate from the motor, which is driven via a plug connection. Additionally, the mobile lifting tripod offers greater flexibility. Batch sizes from 5 to 2,000 liters are covered by the X50, X100, and X200 series. The X100/X50 adapter allows for production of quantities in the range of 5 to 1,000 liters with the X100 series. Through easy cylinder replacement, directed jet mixing, mixing dispersion, dispersion, suction, and powder wetting can be achieved. Power: 1.5 kW – 7.5 kW Voltage: 230 / 400 V, 50 / 60 Hz Immersion piece: Steel 1.4404 (AISI 316 L)...

... discharge/processing machine — Pneumatic rotary cylinder for automatic opening and closing of the container discharge flap Options — Pneumatic rotary cylinder for opening/closing the container discharge flap (infinitely variable) — Sensor for product monitoring in the downpipe — Control for discharge station, external or local — Replaceable downpipe — Vibration motor or hammer for discharge support with poorly flowing products Discharge support...

... - Hard chrome-plated cylinder shaft - Extremely strong design of piston, cylinder, and pressure bearing - Excellent sealing of the cylinders - Easy installation, as all components are mounted on a base plate - For dual rudder systems, two separate cylinders with adjustable push rods are available - Operation via hand pump, electric motor, or main engine...

...Hydraulic press with electric motor for the workshop. Fully hydraulic press - Hydraulic workshop press with a pressure force of 30 to 1000 tons. Technical data: - 400 mm double-acting stroke - movable cylinder - Pressure display with manometer - 2 operating modes: electric operation or manual operation - 2 independent hydraulic pumps - Control unit with motor protection monitoring and safety...

... implemented for the first time by hyco vacuum technology using a magnetic coupling, achieves a hermetic seal. The pump operates more quietly. In the event of a membrane rupture in the pump, there is no loss, as the design principle ensures that there is no leakage. Contactless transmission is guaranteed, as mechanical transmission is completely absent due to the independent bearing of the pump, and an additional seal to the motor is present.

...In the development of the new two-handed orbital sander with gearbox, special emphasis was placed on operator comfort, durability, and versatility. The sanders provide excellent finishes on wood and composite materials, as well as on hard surfaces, fiberglass, metal, and stone. Double output bearings, the cylinder made of hardened alloy steel, and the 8-blade motor ensure durability. The...

... cylinder to be driven has a high intake volume. Additionally, the cooling performance of the tank is improved. A flow control valve is installed for lowering the load. Operating voltage: 400 V / 50 Hz (480V / 60 Hz); 3-phase Motor power: 5.5 kW; S3-25% Flow rate: 17.4 l/min Operating pressure: 171 bar Control voltage: 24V DC Tank volume: 40 liters Pump type: External gear pump...

... start the engine is significantly reduced. The starting behavior is influenced, among other factors, by the design of the throttle bore. The closing force [3] of the decompression valve is adjusted to the existing pressure in the cylinder to achieve optimal closing behavior. The valve closes automatically with the first ignition cycle. The installation height [4] is adapted to the desired installation situation.

... (EN 558 Series 20), DN 350 - DN 800 (Factory standard) Flange standards::Handwheel, Ratchet, Chain wheel, Worm gear, Pneumatic cylinder, Electric motor, Hydraulic cylinder Marking::EN 19 Leakage testing::EN 12266 (Leak rate A), ISO 5208 Class A Temperature range::max. 180 °C Drive::Handwheel, Ratchet, Chain wheel, Worm gear, Pneumatic cylinder, Electric motor, Hydraulic cylinder Max. operating pressure::DN 80 - DN 350: 10 bar, DN 400 - DN 600: 6 bar, DN 700 - DN 800: 4 bar...

..."]},"quality":["top quality that convinces","universally applicable for hobby and craft","fully automatic operation with pressure switch","pressure reducer for stepless adjustment of working pressure","built-in motor protection prevents the electric motor from overload","powder-coated tank","2 years warranty on compressors","10 years warranty on tank"],"order_info":{"effective delivery quantity":"170 l...

... system. This results in significantly shorter drilling times compared to conventional drilling units. Another special feature is that the oil brake cylinder can move the full stroke of the drilling unit in both feed and rapid traverse. In the standard version, the feed is activated via a signal and a reed switch.