power supply modules Germany

...The Dragonfly battery is designed to enable measurements in areas where power is not available from the local power grid. •,Capacity of 100Wh (power supply of a typical Dragonfly amplifier for up to 10h runtime) •,One battery module can also power several Dragonfly amplifiers (with correspondingly shortened runtime) •,Several modules can be combined to extend battery life. •,Can be used as a UPS (Uninterruptible Power Supply).

...The IM82-24 series switch-mode power supplies are suitable for 24 V power supply of DC consumers, particularly for interface modules from our IM, IMS, and IMC series. The devices are mounted on DIN rails and meet the protection class IP20. The output current is – depending on the type – 2.5 A, 5 A, 10 A, or 20 A. With the wide input voltage range, the power supplies can be used worldwide. Additional features include high efficiency, temperature resistance, and dynamic overload capability.

...Used for protection against power outages as well as under- and over-voltage wipos UPS: Input DC UPS 24-30: 22.5-28 V / 35 A UPS 20-960 UPS-DC/DC combination device: 12-48 V / 20 A...

...DC-DC converters of the SMM (1.5W), SMN (2.5W), and RMM (1.5W) series are cost-effective high-voltage modules for PCB mounting with output voltages up to 15kV. The output voltage is proportional to the input voltage. By using an external feedback, a regulated output voltage can be generated if needed. Application notes provide a selection of such circuits. In the DC-DC converters of the RMM series, the output is highly isolated from the input, allowing the modules to be used with either negative or positive output voltage (output reversible).

...At J. Schneider Elektrotechnik GmbH, you not only get the ultracapacitor modules (UC modules), but also the appropriate charger depending on the application. This way, you receive a coordinated system from a single source. If you cannot find a suitable UC module in our standard range, we would be happy to develop one for you upon request. Whether it’s about a specific housing or the electrical values, we are here to assist you in obtaining the right UC module for your specific application.

...In-line filters for currents from 0.5A to 1000A in various designs. A comprehensive range of EMC filters for single-phase and three-phase systems. In addition to in-line filters up to 1000A rated current, there are also IEC input filters combined with switches/fuses or small modules for printed circuit board mounting. In all power classes, there are both 2-stage filters with a very wide attenuation spectrum and 1-stage filters for a more narrowly defined interference spectrum. For connection, there are variants with screw terminals, plug connectors, or threaded bolts.

... DC for the supply of plant instrumentation. They can be used together with power feed modules. FieldConnex® is the optimal infrastructure for connecting fieldbus devices. The efficient design of the fieldbus power supplies ensures easy deployment and high availability. Power Hubs are power supply systems using termination board technology and can supply up to four FOUNDATION Fieldbus H1 or PROFIBUS PA segments.

...The PSC303 series power supply modules are very compact DC/DC converters with an optimized circuit design, resulting in high power density.

... & inspection Upon request, we are also happy to offer you on-site service including telephone support. Our extensive spare parts inventory with over 100,000 immediately available assemblies enables quick spare parts supply with minimal machine downtime costs for our customers. As the only company worldwide in the control & drive industry, we hold the status of "Bosch Rexroth Service Point." Therefore, we are able to provide you with a 24-month warranty* on the aforementioned repair services and spare parts for power supply modules from the manufacturer Bosch Rexroth/Indramat.

...The new B3 Battery is a battery motor designed for demanding and efficient pumping applications. Its independent power supply allows for maximum flexibility with the highest flow rate of any battery pump in the world (up to 180 l/min). Perfect for extracting or transferring concentrated acids and alkalis. * Media examples: hydrochloric acid, chromic acid, sulfuric acid, nitric acid, hydrofluoric...

... fully flowing sensor - Maintenance-free - Power supply / voltage supply 24 V ± 10% - Mechanical Luerlock connection according to DIN EN 1707 -... Output signal: 0.1 to 10V Operating temperature: 15 to 45°C Flow rate: up to 100 ml/min (depending on the medium) Electrical connection: Material functional channel Material functional channel: FFKM Material housing: anodized aluminum Material encapsulation: PU Mechanical connection: LUER-LOCK DIN EN 1707 Measuring range: 0 to 16 bar Power supply: 12 to 30 VDC...

...-level controller e.g. a PLC. Functions:Temperature control, system monitoring, fieldbus communication, bus coupler for up to 7 MHS power mo Field bus interfaces:CANopen Interfaces:1 x Ethernet 10/100Mbit (on request)  Modul bus:Data communication via CAN, electronic supply 24 VDC  Status indication:Heating system, EtherCAT, CANopen, DC power supply  Integrated I/Os:on request: 8 x DI: input delay...

...Discover the HVC-60005-A1 BMS controller, which is part of our modular ARK HV battery pack for PV or solar systems. With our ARK HV battery system, we offer you a minimum of 3 to a maximum of 10 battery modules with an impressive capacity of up to 2.56 kWh. Connect these modules together to create a customized power supply system with a capacity ranging from 6.9 to 24 kWh. In our online shop...

... materials: PMMA, optional: PEEK™; valve: PEEK™, FFPM optional: PPS, FPM, EPDM; volume flow sensor: borosilicate Seal materials: FPM, optional: EPDM, FFPM Electronics: ARM Cortex M3 microprocessor Motor: brushless DC-motor (BLDC); nominal voltage 24 V, torque 3.3 mNm; analog hall sensors Electrical connection: D-sub plug, 15-pole (male connector) Power supply: 24 V DC ±10 %, max. 1.5 A Interface: RS-232...

...-independent alarms OPC server for integration into the line control system Analog or digital output modules Measurement range: 100 to 350 °C Accuracy: ±3 °C Fidelity: ±1 °C Optical resolution: 225:1 (50% energy) Ambient temperature: 0 to 50 °C; with water cooling up to 180 °C Scanning angle: 90° Measurement points per line: Up to 1024 Power supply: 24 VDC ± 25%, 1 A Ethernet communication: TCP/IP 10/100 Mbit/s Serial communication: RS485 Analog outputs: 3 x 4 – 20 mA Alarm output: Relay, contacts: 30 V, 1 A...

... automated measuring and sorting Display I/O Status 3 different interfaces (USB stick, SD card, LAN) for data storage, data transfer, and parameterization Various menu languages selectable (English, German, Japanese) Channels: 32 Measuring Probes of the DK or DT Series LCD Display: For displaying up to 16 channels Interface Modules: MG80-MA: Main Module; MG80-CM: Counter Module; MG80-LM: Trigger Module Measurement Functions: IST/MAX/MIN/P-P Value Calculation: ADD/SUB Function Power Supply: 10.8 - 26.4V DC...

...The CAR amplifier cassettes allow for the installation of 2 5B measurement amplifiers for galvanic isolation and signal adaptation to all industry-standard sensors. • 5B compatible • 2 amplifier slots per module • 2 monitor outputs • Sensor power supply via pluggable DC/DC converters • 19" format (3U) • easy to plug in The pluggable modules enable the flexible construction of powerful data...

...Double-walled ISO transport tank and storage tank; Centaur® tank modules with ISO transport frame The Centaur modules enable a flexible, stationary fuel supply. Up to 5 Centaur TC-QI-3000F can be mounted on a 20 ft ISO standard transport frame. With the piping and its own control system, it is possible to use them to supply decentralized units with minimal equipment. The unit only requires signals for the fuel levels of the day tank and the power supply for the tank modules. The Centaur tank modules can be transported filled, making them versatile in application.

... ✓ Extended functionality by UPScom management software ✓ 3 years warranty The compact DC UPS modules UPSI-2412DP2 in a robust DIN rail housing are ideally suited for long-term use in control cabinet applications and decentralized solutions for protecting embedded industrial PCs, controls, motor drives, sensors, measurement devices, safety technology and many more. The UPS comes with USB & RS232...

...PWM4 (BCU 144/PWM/4CH) is a Bluetooth controllable, four channel PWM dimmer for constant voltage LED loads, such as LED strips and constant voltage LED modules. It is connected between a 12-24 V DC power supply and the constant voltage LED load. PWM4 can control up to four channels making it an ideal partner for RGBW, RGB and tunable white (TW) applications. The maximum combined output current is...

...Continuous selfsupervision. Vacuum circuit breakers equipped with the CM16 control module continuously monitors control, switching modules, functional wiring and auxiliary power supply quality. CM16 eliminates the necessity of additional trip and close coils, charging mechanisms and all related wiring supervision. The whole trip and close circuit supervision comes in single package with any...

...Part Number:BGB12864-09A ● Character LCD 128 x 64 (dots) ● FSTN-Gray / STN-Gray / STN-YG / STN-Blue ● Bulit-in controller ((NT7108C or Equivalent) ● +3.3V / +5.0V power supply ● 1/64 duty , 1/9bias ● Viewing Direction: 6H / 12H ● Interface: 6800 4/8-bit parallel ● Backlight (Side LED): White / Green / Blue / Yellow-Green / RGB / Orange / Amber ● Temp: N.T / W.T / Super W.T...

...• 5 years SITOLUX warranty • 50,000 hours lifespan • LEDs and power supply are replaceable • Aluminum heat sink • Additional 5 years warranty after replacement of the LED unit and power supply by our service center • Optimal heat dissipation through innovative cooling system • Stable construction and anodized surface • High-quality SMD LEDs from Lumileds LUXEON • Power supply technology Meanwell HLG series • Flexible tilting of individual modules • Custom lens configuration for individual modules possible...

... length or mains cable Optional, on request: Output power: 20Watts and more Optional, on request: Combined variant with connector and cable Optional, on request: Customized output voltages Optional, on request: Current regulated version for LED application...

...Weighing display with integrated weighing technology The ideal solution for automatic/self-service weighing stations Splash protection IP65 and stainless steel design Integrated Windows PC, WIN10 7" TFT color display Resistive industrial touch screen Network: Ethernet 10/100/1000 Mbps Interfaces: 2 x USB, optional RS232 Internal power supply dimensions: Length 384mm, Width 170mm, Height 75mm...

...AUTEC DIN RAIL is a receiving unit designed for installation in the control cabinet of a machine. The receiving unit is mounted by simply snapping it onto a DIN rail in the control cabinet. It consists of at least one "CPU MODULE" and a power supply module ("POWER SUPPLY MODULE"). The power supply module is available in either AC or DC versions. Thanks to its modular design, up to 4 expansion...

...Connection of CANopen devices and networks to PROFINET IO - PROFINET IO Device (1440 input bytes and 1440 output bytes) - CANopen Manager Simple expansion of the CANopen gateway via InRailBus - Design according to PROFIBUS International Document TC2-09-0002 and CANopen specification CiA 309-4 - Connection of CAN and power supply can also be made via InRailBus - CAN-CBX-I/O modules can be connected to the gateway via InRailBus without additional wiring Software tools included - PROFINET IO configuration tool GSDML-Composer - Additional free software tools for esd-CAN boards (e.g., CANreal)...

...DAC-MOS II 500D Module Block The DAC-MOS-500-D module block is built on the same base board as all other DAC-MOS II modules, thus having the same connection layout. To fully utilize its performance, a supply voltage of ± 75-80V is required, and a low-resistance, i.e., high-capacity power supply must be used. Only a power supply with ≥ 80000 µF/85V using the ring core transformers RK-75M, RK-95M...

...The displacement transducers work according to the principle of the differential choke (inductive half bridges). They consist of two coils which are encapsulated in a Mu metal cylinder in a sealed and vibration-proof manner. A Mu-metal plunger causes an opposite induction change in the two coils when displaced by the hollow coil body. The displacement transducers are designed for an oscillator frequency of 10 kHz. Power supply and signal conditioning are provided by external module modules. Interface:SSI Measuring ranges available:80-360mm Special feature:External electronics, Full casting...

...1-PHASE DOOR CONTROL (110V-240V) FOR DOOR DRIVES UP TO 1.2 KW (8A), UP TO 60% DUTY CYCLE, 24 VOLT POWER SUPPLY (500MA) • Soft start and braking provide maximum material protection and a long product lifespan • Fast acceleration speeds up process flows and reduces waiting times • Extremely easy installation thanks to extensive presets for standard door systems and self-learning automatic...