welded plates Belgium

...Controlled by thermostatic valve High-performance cast iron burners Temperature regulation up to 285 ºC Independent cooking zones Fully welded cooking surface 50-micron hard chrome plating AISI 304 stainless steel body Very large capacity grease drawer Integrated splash guard Optional support and wheels CLAM+ G available for cooking on both sides Completely grooved surface, upon request Optional...

... 1.4845 - Duplex pipes UNS S31803 1.4462 - Super duplex pipes UNS S32750 S32760 1.4410 1.4501 - Solid duplex and super duplex round bars 1.4462 1.4410 1.4501 - Stainless steel sheet 1.4301 304L 1.4404 316L 1.4571 316TI, 321, 1.4541 - Heat-resistant plate 309 1.4828 1.4833 310 310S 1.4841 1.4845 - Duplex plates UNS S31803 1.4462 - Super duplex plates UNS S32750 S32760 1.4410 1.4501...

...This standard tank from our stock has been equipped with an electric 16 kW tracing system to raise a product from 15 °C to 80 °C in 2.5 hours. Insulation and a bolted decorative plate have been added around the tracing. We can also offer welded decorative plates. A 4 kW agitator has also been installed on the tank, featuring an axial/radial Alabnet impeller and a halbanker in combination with 3 x deflector plates.

...The welded mesh swing gate from Kopal has been designed to perfectly integrate with this type of fencing. The swing gate is made of angle-welded steel tubes. The dimensions of the tubes depend on the length of the leaf. The swing gate is filled with double welded mesh, which is welded into the frame. Other fillings such as sheets or perforated plates are available upon special request and are...

... resistors, placed beneath the plate. Devices built in compliance with current regulations (CE). PLUS: Stamped plate, made in one piece with the TOP of the device, hygiene guaranteed at 100%! Reference: E17/PL4T-230/3--N Kw Electric: 4.5 Electrical Connection: 230/3 50-60Hz Family: Cooking Plates Sub-Family: Electric...

... transport. The roof: It is flat and made of electro-galvanized trapezoidal plates (thickness 0.75 mm). On these plates, we find 20 mm thick styrofoam insulation. The entire structure rests on profiled tubes of 60/30/1.5 placed every 60 cm and welded to the longitudinal wall (or to the load-bearing beam in the case of an open construction for coupling). Between these profiled tubes, there is a 15 mm static insulating air gap and below that, another 40 mm of rock wool...

...-free - Brake tester with automatic stop in case of slip with needle standstill and automatic restart - Extra large rollers for maximum contact with the tires and a perfect brake test - Electronic measuring system with strain gauges - Self-supporting closed chassis - Choice of welded or epoxy rollers - TUV and CE approved Several options are available, such as analog difference indication or via red lamp, drive-over plates, readout on foot or hinge, printer, remote control, etc.

...STRUCTURE PANEL Tubular - A42sc steel of appropriate section and fully welded, including uprights and intermediate crossbars. Reinforcements made of 300 mm long, 10 mm thick steel are welded to the outside of the upright tubes at the location of the guide rollers. The welds are not visible. COATING ON SAS SIDE Made of 4 mm thick A42sc steel plates welded to the panel structure. These welds are...

... Minebea Intec Combics indicators, QCT01 or isi terminals. IF Floor Scales Painted - 1 x 3,000e or 2 x 3,000e (verifiable as legal for trade in accuracy class III) or 15,000d or 30,000d (not for use in legal metrology) - Construction featuring metal plates with pressed edges (no welded seams) - Exceptionally low-profile design (starting at 25mm) - IP65 protection rating - Including drive-on ramp - Rugged, industrial-grade construction - Optionally with connection endplate Accuracy class III:1 x 3,000e or 2 x 3,000e Weighing range:150 up to 3000 kg IP protection rate:IP65 or IP68...

...The DS machine is designed for the efficient drilling and cutting of plates, featuring automatic plate feeding and the automatic removal of cut parts. The machine's portal is based on our MG machine, which is constructed from a heavy welded structure suitable for plasma cutting straight or bevel, oxy-fuel cutting, drilling up to a diameter of 40 mm, and marking with micro-punch pneumatic marking. The machine is designed to automate your production process, thereby saving time and costs.

... description, sketch, or drawing, or on the advice of our design office, individual pieces, prototypes, or custom series are laser cut, bent, turned, milled, ground, welded, and assembled. Everyone is welcome here: engineering and maintenance departments of companies, contractors, and individuals who need components, machines, plates, stairs, railings, etc. We have a large stock of materials to serve you quickly.

Supplier of screw blades, screw tapes, shaftless spirals, mixing spirals, screw blades for (soil) drilling, etc. We also specialize in the production of screw shafts, ranging from standard designs to the most wear-resistant versions possible in welded construction production. Such as with Hardox 400 and 500, Duplex (3CR12) Cobranox, with hard-welded armor plates, round reinforced hard-welded, to...

At Omnimesh, we specialize in the manufacturing and processing of metal mesh and woven products, as well as their conversion into finished products. Check out our industrial products and discover our filter mesh, welded grids, woven grids, perforated plates, chimney grilles, spark curtains, and much more! As a manufacturer of metal mesh, we have specialized in the application of screen (re...

We are the company Van Beeck René and operate as a stockholding trader in the field of new, welded, second-choice steel pipes, beams, L and U profiles, plates, vade mecum, rebar, construction steel, Inox, aluminum, and trade steel.