WATERGATES GMBH & CO. KG

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 9 and 11! Body GG-25 (grey cast iron), epoxy coated 120 … 180µm (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge bidirectional Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the table Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Refer to the advices on page 8! Body Stainless steel 1.4408 Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Pneumatic single acting with spring return, normally closed (NC). Pressure discharge One-sided Pilot pressure 6bar Pilot Media Filtered and dried, slightly oiled air according to ISO 8573 (please refer to the data sheet) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 Installation Only with vertical upwards actuator The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy-coated (heattreatment 190°C, 20min) Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (304) Stem Stainless steel 1.4305 (304) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the table Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 2 parts to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquids, drain water, sludge, food etc. (viscous media, pulverised media with fibre particles, plastic granulates, sand or similar media on request). Not suitable for steam. Body GG-25 (grey cast iron), epoxy coated (heattreatment 190°C, 20min) Sealing • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4301 (AISI 304) Stem Stainless steel 1.4305 (AISI 304) Function Electrical operated Pressure discharge bidirectional Stem Not rising Pressure range Please refer to the data sheet Temperature range • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data Design Center body consists of 1 part to be mounted between two flanges according to EN 1092-1 type 11 form B – PN10 (former DIN 2501). ANSI 150 on request. Media Liquid and pulverised media with fibre particles, viscous media, drain water, sludge, food etc. (plastic granulates, sand or similar media on request). Not suitable for steam. Body Stainless steel 1.4408. Sealing • Metal/metal • NBR • EPDM (FKM or PTFE on request) Gland 3-piece sealing set: • 1x GFO®-Faser – TWARON® edge reinforced • 1x O-ring (NBR or EPDM or FKM) • 1x synthetic fiber, PTFE-lubricated Knife Stainless steel 1.4401 (316) Stem Stainless steel 1.4404 (316) Function Electric acting Pressure discharge One-sided Voltage 400V 3AC (24V DC, 230V AC on request) Pressure range Please refer to the data sheet Temperature range • metal: on request • NBR: -25°C … +90°C • EPDM: -35°C … +120°C Attention: Temperature range not for all media. Face to face EN 558-1 Row 20 The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice! TWARON® is a registered trademark of Teijin Aramid

Technical data In general The actuator is especially suitable for the operation of ball valves and butterfly valves with 90°-rotation angle. Features robust, water-resistant body made of aluminium optical position indicator, illuminated at end-positions compact body design manual override heating device against condensed water additional potential-free limit switches Material Carbon Steel, Aluminium Alloy, Bronze Body polyester coated Installation Vertical as the picture shows. All other installations only after request. Ambient temperature -20°C … +70°C Mounting pad DIN-ISO 5211 Standard voltages 24V DC 230V 50/60Hz ±10% tolerance others on request Protection IP 67 Cable entry 2 x M20x1,5 End stops 2 limit switches. Operating angle 90° ±5° Heater 3W Duty cycle 50% The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data In general The actuator is especially suitable for the operation of ball valves and butterfly valves with 90°-rotation angle. A waterresistant body with overload protection and a heating device against condensation water. Material Carbon Steel, Aluminium Alloy, Bronze Body polyester coated Installation Vertical as the picture shows. All other installations only after request. Ambient temperature -20°C … +70°C Mounting pad DIN-ISO 5211 Standard voltages 24V DC/AC, 230V AC others on request Protection IP 67 ATEX-Protective class (Option) II 2G EEx d IIB T4 Cable entry 2 x M20x1,5 Protection devices Motor thermostat End stops 2 limit switches. Operating angle 90° ±5° Heater 5W Duty cycle 75% Standard equipment 2 additional limit switches, optical position indicator with add. LED, manual override. Option Please refer to the data sheet The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data In general The actuator is especially suitable for the operation of ball valves and butterfly valves with 90°-rotation angle. A waterresistant body with overload protection and a heating device against condensation water. Materials Carbon Steel, Aluminium Alloy, Bronze Body polyester coated Installation Vertical as the picture shows. All other installations only after request. Ambient temperature -20°C … +70°C Mounting pad DIN-ISO 5211 Standard voltages 24V DC (only up to NA028) 230V AC, 400V 3AC others on request Protection IP 67 ATEX-Protective class (Option) II 2G EEx d IIB T4 Cable entry 2 x M20x1,5 Protection devices 2 (OPEN/CLOSE) torque switches, Motor thermostat End stops 2 limit switches. Operating angle 90° ±5° Heater 20W Duty cycle 25 … 50% Standard equipment 2 additional limit switches, optical position indicator, manual override. Option Please refer to the data sheet The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data Design Gate valve, with internal spindle, acc. to DIN 3352/4A, soft sealing, maintenance free. For the use of process water and wastewater. Features • The inside and outside surfaces of the valve are FBE-coated. • In case of leakage of the stem seals, the seals can be replaced under media pressure. • Low dead space and the flat valve seat guarantee a great flow characteristic and prevent product deposition. • Bidirectional pressure discharge. • Permission and marking acc. to directive 97/23/EG (Pressure Equipment Directive) Face to face EN 558-1 Row 14 (former DIN 3202 F4) Connection Flange DN40 … DN150, PN16 drilled, Flange DN200 … DN400, PN10 drilled. Flanges DN65 – PN16 will be delivered in 4-hole execution! Mounting position vertical preferred Pressure Range PN10 … PN16, see table Temperature Range 0°C … +80°C Material Body: GGG-50, FBE-coated Stem: Stainless steel Wedge: GGG-40/Brass/EPDM (NBR on request) Stem seals: EPDM (NBR) The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!

Technical data Design Swing-check valve, body and top cover FBE-coated. Face to face EN 558-1 Row 48 Connection Flange DN50 … DN150, PN16 drilled, Flange DN200 … DN300, PN10 drilled. Flanges DN65 – PN16 will be delivered in 4-hole execution! Mounting position In horizontal pipes with above standing top cover, observe to the flow direction! Pressure range PN10 … PN16, see table Temperature range 0°C … +80°C Material Body: GGG-50, FBE-coated Top Cap: GGG-50, FBE-coated Stem: Stainless steel Seat: Bronze Seat seals: • EPDM • NBR The above information is intended for guidance only and the company reserves the right to change any data herein without prior notice!