IGUS® GMBH - motion plastics® - tech up, cost down!

Diameter [mm]: length [mm]: iglidur® W300 - Material data iglidur® W300 - The continuous runner for maximum holding times. iglidur® W300 - Material data Polymer bearings applications overview Polymere bearings application examples overview Polymer bearings applications overview iglidur® W300: The endurance runner For extremely high service life in continuous operation Low coefficient of friction extreme high wear-resistance Suited for rough shafts and stainless steel shafts Dirt resistant Diameter [mm]: length [mm]: iglidur® W300 - Material data iglidur® W300 - The continuous runner for maximum holding times. iglidur® W300 - Material data Polymer bearings applications overview Polymere bearings application examples overview Polymer bearings applications overview

Free design iglidur® A350 plate material for free design: FDA-complied and wear-resistant at high temperatures comply with the requirements of the FDA for application up to +180°C For medium till high loads well-suited for rotations and oscillating applications Application areas:Food area General features iglidur® A350 Density 1,42 g/cm 3 Colour blue moisture absorption at 23 °C and 50 %r.h. 0,6 Wt.-% Max. water absorption 1,9 Wt.-% Physical and thermal properties iglidur® A350 Max. long term application temperature +180 °C Max. short term application temperature +210 °C Lower application temperature –100 °C Mechanical properties iglidur® A350 Max. permissible static surface pressure (+20 °C) 60 MPa Shore D hardness 76 Electrical properties iglidur® A350 Surface resistance > 10 11 Ω

iglidur® plate material Free design iglidur® J - the Fast-and-slow motion specialist - now available as plate material for free design. wear-resistant Lubrication-free Multi-purpose Good chemical resistance Lowest humidity absorption Application areas:Plant construction, fixtures, prototype construction, special machinery construction iglidur® plate material Free design iglidur® J - the Fast-and-slow motion specialist - now available as plate material for free design. wear-resistant Lubrication-free Multi-purpose Good chemical resistance Lowest humidity absorption Application areas:Plant construction, fixtures, prototype construction, special machinery construction General features Density 1,49 g/cm 3 Colour yellow Max. moisture absorption at 23 °C and 50 %r.h. 0,3 Wt.-% Max. water absorption 1,3 Wt.-% Mechanical properties Max. permissible static surface pressure (+20 °C) 35 MPa Shore D hardness 74 Physical and thermal properties Max. long term application temperature 90 °C Max. short term application temperature 120 °C Lower application temperature -50 °C Electrical properties Surface resistance 10 12 Ω

drylin® SAW-1040 linear module, drylin® W aluminium profile, surface: hard-anodised, Trapezoidal lead screw TR10x2, machined lead screw end 69x15mm, guide carriage, aluminium shaft end support. Stroke length: 500mm, carriage length: 69mm, NEMA23 stepper motor with JST connector. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

ZLN miniature toothed belt axis based on the low-profile guide system drylin® N. System width 40mm, installation height 28mm. Ready-to-install system with stepper motors or BLDC/DC motors. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® ZLW-0630 basic toothed belt axis, basic version, feed rate 54mm/rev, aluminium profile, surface: hard-anodised, neoprene toothed belt in black, guide carriage length 60mm, shaft end support made of aluminium, alignment of drive pin on the right, stepper motor with stranded wire. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SLW-1040 linear module, drylin® W aluminium profile, surface: hard-anodised, ball bearing Trapezoidal lead screw TR10x2 made of stainless steel, lead screw end machined 6h9x17mm, guide carriage in 100mm length, shaft end support made of anodised aluminium. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

drylin® SHT-12 linear module, drylin® R hard-anodised aluminium shafts, Trapezoidal lead screw TR10x2 made of stainless steel with ball bearings, machined lead screw ends 6h9x17mm, quad blocks, aluminium shaft end support, stroke lengths in 250mm or 500mm. Configure drylin SHT linear modules individually here: https://igus.eu/ddx

The drive technology online configurator gives you the right drive technology system after you enter your requirements. You also have the option of requesting or ordering motors and other accessories, such as the motor control system. - Fast and easy configuration - Optional accessories - Detailed parts list - Fast delivery

Planetary gears for igus® stepper motors NEMA 23, 23XL & 34 Increased motor torque Increased brake holding torque 2 installation sizes Reduction gearing of 3 & 5 available Typical applications:Packaging technology, general mechanical engineering, inspection technology/ camera travel drylin® E data sheet - Gearbox for stepper motors GEA-60-..._EN.pdf Planetary gears for igus® stepper motors NEMA 23, 23XL & 34 Increased motor torque Increased brake holding torque 2 installation sizes Reduction gearing of 3 & 5 available Typical applications:Packaging technology, general mechanical engineering, inspection technology/ camera travel