Black Coating Type 220V 230V 240V Alumina Pellet Igniter

Ceramic Pellet Igniter Information Ceramic Boiler Ignition Igniter surface can reach a permanent working temperature above 900℃;Since air can through and around inside and outside of the heater tube. Heat can be transferred from both inside and outside of ther heater element. Igniting wood chips, firewood, coal bricks or other biomass fuel. Specification: Voltage: 120V / 230V Power: 150W / 170W / 200W / 230W Tube Size: OD10.5 × ID6.5 × L78 mm Supporting Socket: NO.7 Lead wire: 300mm / 400mm / 500mm / 900mm (Customized is accept) Range of temperature: 800~1100 °C Alumina Pellet Igniter Advantages 1) Higher temperature, about twice of traditional metal sheathed heater; 2) Shorter ignition time, about 60~90 seconds 3) Electrically insulated with no exposed electric contacts 4) Wear and corrosion resistance 5) Long life time 6) Easy to install and replace 7) Long-lasting (non-aging). Tested to 100,000 cycles. 8) 800~1100°C at steady-state temperature.

INNOVACERA® Ceramic hot surface igniters for pellet boilers only need approx. 1/10 of the energy of that needed by hot air fans and ignition blowers. Their ignition capacity lies between 120 and 350 W. Depending on the positioning of the ignition element in the boiler, the ignition time of approx. 60 seconds is extremely short. This also means minimal emissions. Specification: Voltage: 120V / 230V Power: 300W / 350W Tube Size: OD11.5 × ID6.5 × L108 mm Supporting Socket: NO.43 Lead wire: 300mm / 400mm / 500mm / 900mm (Customized is accept) Range of temperature: 800~1100 °C Applications: Kerosene fan heater Wood pellet, wood chips stove or boiler Small scale biomass industrial furnace ignition Incense burner

INNOVACERA Alumina Ceramic hot surface igniters for pellet boilers only need approx. 1/10 of the energy needed by hot air fans and ignition blowers.Their ignition capacity lies between 120 and 350 W. Depending on the positioning of the ignition element in the boiler, the ignition time of approx. 60 seconds is extremely short. This also means minimal emissions. Alumina Ceramic Heater Specification: > Voltage: 120V/230V > Power: 160W, 180W, 210W, 225W, 230W, 240W, 255W > Tube Size: OD10.5 × ID6.5 × L90 mm > Supporting Socket: NO.4/NO.5/NO.6/NO.29 > Lead wire: 300mm/400mm/500mm/900mm (Customized is accept) > Range of temperature: 800~1100 °C Ceramic igniter technology benefits: * A fraction of the energy consumption compared to element heater. * Long-lasting (non-aging). * Time to ignition 60~90 seconds. * Tested to 100,000 cycles. * Easy to install and retrofit. * 800~1100°C at steady-state temperature. * Impervious to oxidation and corrosion.

Electric 12V 13V Alumina Ceramic Heating Element Heater Rod for Oxygen Sensor Advantages Ceramic Heater for Oxygen senster is used for heating oxygen sensors that detect the exhaust gas of vehicles and is equipped to most of automobile gasoline engines. Because the temperature can be rapidly raised, it is possible to activate the sensor immediately after the engine start which provides useful feedback to reduce emissions. 1.Based material: a.white alumina ceramic b.the content of alumina is no less than 95%. c.the tungsten slurry is printed on the ceramic tape, laminated by hot pressing, and thensintered under the protection of a hydrogen atmosphere at 1650 ° C 2.Ni-wires:N6 Ni-wires with 0.6mm diameter 3.Brazing material: siliver-copper braging alloy