Zinc-plated steel - Import export

Plate die-cast zinc or stainless steel 1.4305. Anti-slip plate thermoplastic elastomer. Version: Die-cast zinc plate, black powder-coated. Stainless steel plate, bright. Note: Swivel feet consist of a plate and a threaded spindle or ball joint. Any plate can be combined with any threaded spindle or ball joint. The anti-slip plate absorbs vibrations and prevents the swivel foot slipping. For matching threaded spindles see 27810. For matching ball joints see 27811.

Steel 1.0718 or stainless steel 1.4305. Version: Electro zinc-plated steel. Bright stainless steel. Note: Pin with groove, suitable for DIN 71752 clevis. Secured with a DIN 6799 E-type circlip (alternatively a KL or SL clip). When combined with a suitable clevis and tang, forms a fully functional clevis joint.

Material, version: 1. Sealing cap red Polyamide 66 thermoplastic. 2. Filler sieve black Polypropylene thermoplastic. 3 Flange electro zinc-plated steel. 4. Fastening screws electro zinc-plated steel. 5 Flange seal cork. 6. Chain brass.

Steel or stainless steel 1.4404. Version: Steel electro zinc-plated. Stainless steel bright.

Steel 1.0718 or stainless steel 1.4305. Version: Steel electro zinc-plated. Stainless steel bright.

Steel. Stainless steel 1.4305. Stainless steel A4 1.4401. Version: Steel electro zinc-plated. Stainless steel bright. Note: Block hinges with fastening nuts and extended middle section for inset doors. Mounted with nuts (M6 or M8) from inside. The hinge can be mounted left or right. The opening angle is 180°. Supplied unassembled. Fastening nuts and washers are supplied.

Suitable for emergency stop and continuous use Energy reduction: 58% to 73% Dynamic force absorption: 870 N to 35190 N Impact velocity: max. 5 m/s. The profile dampers are maintenance-free and are supplied ready to install with a special fastening screw. Environment: Resistant to microbes, sea water, chemicals and with very good UV and ozone resistance. No water absorption or maceration. Fastening screws: Special cap screws with hex sockets, material 44SMn28 (free-cutting steel SAE 1144) electro zinc-plated: M6x9, M6x10, M8x14, M12x18, M16x26 ISO 4762 cap screws with hex sockets - 8.8 steel, black: M3x6, M4x8**, M5x10** ** With DIN 125 washer, electro zinc-plated steel. Application: Linear slides and linear guides, pneumatic cylinders, handling equipment, machines and plants

Steel 1.0037. Aluminium EN AW-6060. Version: Steel electro zinc-plated. Aluminium anodised. Note: The machined tolerances of these round and square tubes are individually matched to the tube clamping system. *Square aluminium size 10x10 are only available as solid bars. On request: - Custom cut length (L max. 5000 mm) - Stainless steel tube (L max. 3000 mm)

Metal parts, steel grade 5.6. Elastomer, natural rubber, medium hardness, Shore 60. Version: Steel electro zinc-plated. Note: These machine feet have proven themselves to be universally applicable elements for the elastic support of all types of machine. They are commonly used wherever large horizontal movements are to be avoided. The horizontal rigidity is higher in all directions than the vertical rigidity. If used correctly they are excellent at preventing the transfer of vibration and noise. Machine feet with shear protection are available for situations where tensile forces are to be expected. The indicated load data are reference values for static loads by rubber hardness of Shore 60A. In contrast to those in the drawing, the holes D2 can also be elongated holes.

Outer body steel. Mounting bush plastic. Version: Steel electro zinc-plated. Note: Rotation dampers are maintenance-free, ready-to-install elements for the controlled braking and damping of rotational or linear movements. These rotation dampers enable the smooth opening and closing of small covers, compartments and drawers. They protect sensitive components and can also raise the quality and value of products. The rotation dampers brake right or left rotations or in both directions. One cycle rate corresponds to one 360° right rotation and one 360° left rotation. Attention: The rotation damper bush should not be used as a support, but rather as an external guide or bearing.

step spacer material: steel finish: zinc plated size: diameter 25.40 mm, height 20.60 mm manufactured by CNC turning Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.

Lock Nut material: cold rolled steel finish: zinc plated outer diameter: 0.625 +/- 0.015 inch height: 0.125 +/- 0.015 inch internal thread: 3/8-24 UNF - 2B Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.

deck lift nut manufactured by CNC turning and milling material: steel finish: zinc plate with yellow chrome outer diameter: 1 inch inner diameter: 0.6 inch height: 0.59 inch inner thread: 3/8 - 16 UNC - 2B Soochow Advance Industries Co., Ltd., (website: www.sai-parts.com) supplies custom OEM mechanical parts, industrial fasteners, screws, bolts, nuts, industrial fittings, electronic hardware by precision CNC machining, CNC turning, CNC milling, CNC engineering.

Flat washers ~DIN 125 (~DIN EN ISO 7089) form A Material: zinc-plated steel (final digits 52) stainless steel (final digits 53)

Countersunk screws - metal ~DIN 963 (~DIN EN ISO 2009) Material: machining steel 4.8 zinc-plated

Hexagon head screws - metal ~DIN 933 (~DIN EN ISO 4017, threaded to head) Material: machining steel 4.8 zinc-plated

Pan head screws - metal ~DIN 85 (~DIN EN ISO 1580) Material: machining steel 4.8 zinc-plated