Results for
IGUS® GMBH
Germany
iglidur® sealing lip bearing d1 [mm]: Quick and easy-to-mount polymer bushing made of iglidur® J (JDSM) or iglidur® V400 (VDSM) with clip-on radial shaft seal ring as sealing for the rotating shaft. Seals off against dirt, dust as well as all pressure-less media. Polymer bushing with clip-on radial shaft seal ring Sealing for rotating shaft Temperature application range like iglidur® J Coefficient of friction only 10% higher than in iglidur® J Coefficients of friction identically exceptional like iglidur® J Reduced installation space as well as easy and simple mounting Realizable with numerous sealing types High-temperature option VDSM possible Temperatures till 150° C Material: iglidur® J High temperature option VATM, iglidur® V400 Seal ring made of fluorelastomer Bearing-sealing combinations for other applications on request When to use it? When the penetration of dirt and spray water should be prevented When only a small installation space is available in the axial direction When an existing seal should be integrated in a plain bearing When not to use it? When pressurized media should be sealed When absolute impermeability to the shaft and housing is needed continuously We'll gladly do the developing with you iglidur® sealing lip bearing d1 [mm]:
Request for a quoteKOREMA® GMBH & CO.KG
Germany
Each expansion joint is tailor made. Layers of material are assembled on a frame which conforms exactly to the required profile. Bellows type expansion joints incl. or without reinforcing rings/frames. Diaphragms Expansion joints for varying cross sections and transitions. Construction from round to rectangular Construction according to drawings Non-standard high temperature seals Compound movement
Request for a quoteACE STOSSDÄMPFER GMBH
Germany
Energy capacity 56.5 Nm/cycle Stroke 18.7 mm Optimizing PET stretch blow machines: MAXIMACE, the new PET shock absorbers from ACE, shine with longer service life compared to previous solutions and an operating time of over 20 million strokes. They work simply and faster than other shock absorbers and are stronger at the same time. As a result, downtime is reduced and system performance and production volume are increased. This is accomplished by numerous details such as innovative aluminium outer housings for better heat dissipation, improved high temperature seals (up to approx. 107°C), a diaphragm accumulator for faster cycle times and a larger damper chamber which is filled with food-grade oil. All of this significantly contributes to reduced wear and extended service life. These self-adjusting, specialized shock absorbers stand out in their field of PET container production due to their compactness and distinctively colored aluminium bodies.
Request for a quoteACE STOSSDÄMPFER GMBH
Germany
Energy capacity 56.5 Nm/cycle Stroke 18.8 mm Optimizing PET stretch blow machines: MAXIMACE, the new PET shock absorbers from ACE, shine with longer service life compared to previous solutions and an operating time of over 20 million strokes. They work simply and faster than other shock absorbers and are stronger at the same time. As a result, downtime is reduced and system performance and production volume are increased. This is accomplished by numerous details such as innovative aluminium outer housings for better heat dissipation, improved high temperature seals (up to approx. 107°C), a diaphragm accumulator for faster cycle times and a larger damper chamber which is filled with food-grade oil. All of this significantly contributes to reduced wear and extended service life. These self-adjusting, specialized shock absorbers stand out in their field of PET container production due to their compactness and distinctively colored aluminium bodies.
Request for a quoteCIC - KLAUS CZERWONKA
Germany
The CZ series cylinders are manufactured according to ISO 15552 and have diameters between 32 and 125 mm. Standard version in single / double-acting, with magnetic piston and adjustable cushioning. A complete range of accessories for mounting and position sensing is available. Also available in a special version, as a tandem cylinder or with Viton seals for high temperatures. Version with weight-optimized lightweight profile tube including practical slot for position sensors.
Request for a quoteCIC - KLAUS CZERWONKA
Germany
The CY series cylinders are manufactured according to ISO 15552 and have diameters between 32 and 125 mm. Standard version in single / double-acting, with magnetic piston and adjustable cushioning. A complete range of accessories for mounting and position sensing is available. Also available in a special version, as a tandem cylinder or with Viton seals for high temperatures. Version with robust and aesthetic profile tube.
Request for a quoteFRANKE GMBH
Germany
The bearing assemblies are equipped with the S10 boot seal as standard. Temperature: –30 ° C to +80 ° C (NBR). Max. Peripheral speed: 5 m / s. For the sealing of the construction (e.g. when using a bearing element) the seal can be ordered by the meter. The joint is then glued with Loctite 401® adhesive. Special seals are available on request. Franke offers Viton seals for high temperatures or aggressive media.
Request for a quoteHIDROMEC SRL
Italy
The steel industry is a specific sub-sector of the stationary industry. The term steelmaking refers to a specific area of metallurgy that involves the technique of processing iron-rich ore to produce iron or various types of ferrous alloys, including steel, pig iron and alloy steels. The steel industry needs very reliable and robust equipment: no malfunction is allowed. Rolling mills and furnaces must not be stopped by a defective hydraulic cylinder. The main features of the cylinders used in this sector, apart from ensuring high reliability, are that they are designed to operate in dusty environments and at very high ambient temperatures, even above 100°C. This makes it necessary to equip the cylinders with seals that retain their functionality even at such high temperatures. Seals and gaskets made of special fluorocarbonate material (Viton) are used. HIDROMEC develops hydraulic cylinders and systems for applications in the steel industry that are reliable, durable and comply with the relevant environmental standards.
Request for a quotePROEX PACK SP. Z O.O.
Poland
Shrink film is characterised by low sealing temperature, high tensile strength and very high transparency. Production range from 50 to 2500 mm in width. Thickness from 0.020 to 0.300 mm, made in three- layer co-extrusion technology. The hoods perform insulating functions. It is an ideal solution for the protection of materials, susceptible to all weather conditions such as moisture, dust or mud. Standard hoods – two side folds “Y” type hoods – one upper fold
Request for a quoteATAC ELEKTRIK VE MAKINA SANAYI TICARET LTD STI
Turkey
High Performance Ovens is engineered to meet the most critical temperature requirements. They are designed for continuous drying operations at temperatures up to 240°C. Horizontal air flow provides fast heat-up and recovery and ensures rapid drying. Heated air is continuously circulated by turbo blower. A high temperature gasket door seal eliminates air leakage and ensures longer gasket life while being subjected to extreme operational temperatures.
Request for a quoteBEITO
Belgium
Fully synthetic brake fluid of the highest quality, applicable in brake and clutch systems of very heavily loaded automobiles. Intended for changing and refilling the fluid in any vehicles where the instructions of use demand applying either DOT3 or DOT4 fluids. Fully mixable with other fluids of the class DOT3 or DOT4. In older cars, substitutes the R3 fluid applied earlier and thus, improves significantly the vehicle operation safety. Meets the requirements of any and all standards valid in Poland: PN-C-40005:2002, FMVSS 116 DOT 4, SAE J 1703. Features high chemical stability, perfect rheologic characteristics at low and high temperatures. Neutral for sealing components and alloys of metals applied in braking systems.
Request for a quoteSSA PANA FOAMTEC DOO
Serbia
We process polyurethane foams in blocks and in rolls. The main purposes of these raw materials are mainly the protection of sensitive goods during transport, air and water filtration, production of various self-adhesive and non-adhesive foam tapes. They are available in self-extinguishing and standard versions. We produce cut and stamped items from this raw material. Due to the open cell structure, Polyurethane foams are suitable for separating and attenuating sound and vibration. They are also suitable as permanently elastic buffers or as sealing tapes. In addition, they are resistant to many chemicals/solvents and high temperatures. For dust sealing, thermal insulation, sound insulation, shock absorption, vibration separation, upholstery and transport protection.
Request for a quoteSISTO ARMATUREN S.A.
Luxembourg
SISTO-C Pneumatically operated Valves Features ● Piston actuator ● Valve bonnet in compact design, actuator housing and valve bonnet manufactured out of one part ● Stainless steel stem ● Clear visual position indication by red plastic indicator – well visible all around ● Stainless steel compressor ● Floating nut ● Spring chamber venting by operation hole ● Spring to close – air to open ● Stainless steel spiral spring support for MD 65 and larger Variants ● Spring to open – air to close ● Air to open – air to close ● Two-stage-actuator ● High temperature design with FKM/FPM seal (Recommendation: >= 80 °C measured at actuator housing) Optionen / Options ● Limit switches ● Positioner ● Adjustable travel stop
Request for a quoteTWK-ELEKTRONIK GMBH
Germany
The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The model for high temperature use is without shaft seal. Under the rear cover there is a signal changeover switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.
Request for a quoteTWK-ELEKTRONIK GMBH
Germany
The angle transducers have a magnetic scanning according to the HALL principle. Due to the robust design, critical and interference-free applications in harsh environments can be realized. They have a robust housing (wall thickness > 5 mm) made of aluminium or stainless steel, shaft and ball bearing made of stainless steel, shaft with flattening, rotor with shaft and permanent magnet mounted in prechamber, sensor circuit consisting of ASIC with Hall elements and interface electronics housed in closed main chamber. Two models are available: For low and high temperature applications. The model for low-temperature use is equipped with a special grease for bearings and shaft seal. Seals and shaft seal are made of PTFE. Cable gland with clamping jaw pressure screw and silicone seal. The high temperature model is without shaft seal. Under the rear cover, there is a signal path switch (CW/CCW). On the side there is a preset button (4 mA) placed under a screw plug.
Request for a quoteSISTO ARMATUREN S.A.
Luxembourg
SISTO-C Bonnets with piston actuator MD 168-202 Features ● Piston actuator ● Stainless steel actuator housing ● Stainless steel bonnet ● Stainless steel stem ● Clear visual position indication by red plastic indicator – well visible all around ● Stainless steel compressor ● Floating nut ● Spring chamber venting by operation hole ● Spring to close – air to open ● Stainless steel spiral spring support Variants ● Spring to open – air to Close ● Air to open – air to Close ● Aluminium hard anodised actuator housing ● High temperature design with FKM/FPM seal (Recommendation: >= 80 °C measured at actuator housing) Options ● Limit switches ● Positioner ● Adjustable travel stop
Request for a quoteENDRESS+HAUSER AG
Switzerland
Levelflex FMP54 for continuous level measurement in liquids under extreme conditions. The process connection with its ceramic-graphite seal safeguards high temperature and high pressure applications as they occur in steam boilers and toxic media like ammonia. The gas tight feedthrough guarantees additional safety. Only the gas phase compensation of the FMP54 gives reliable results in case of gas and steam phases. Reliable measurement in case of moving surface and foam or in changing medias.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
MICROCERTEC
France
Various methods of assembly exist to bind ceramic to metal. When it comes to make an assembly that can resist to mechanical stresses and/or high temperatures, be vacuum leak tight and withstand corrosive environment, high temperature, braze sealing is essential. Applications Ceramic-to-metal brazed assemblies are particularly suited for use in airborne electronics for the aerospace, defense devices, medical and analytical instruments,high-energy physics, high vacuum equipment, the nuclear industry... We offer customized ceramic to metal brazed assemblies such as for instance : high-voltage feedthroughs for the mass spectrometry, hermetic packages for airborne electronics or sensors for the oil industry, high-voltage hermetic connectors for the nuclear industry, high-voltage insulators for electron tubes.
Request for a quoteINDUSTRIAL BRUSHWARE LIMITED T/A IBEX INDUSTRIAL BRUSHES
United Kingdom
Ibex Industrial Brushes developed flexible closures that remain constant through variable temperatures from -195C to 200C. Suitable for all extreme weather conditions and guaranteed for specific life spans. Please contact us for visuals of these products.
Request for a quoteMIKROPOR
Turkey
Introducing the MVHHT Series: High-temperature filters built to withstand the heat. Crafted with micro glass fiber media and separator, available in stainless steel or galvanized steel frames. Resilient up to 250 degrees, these filters are essential for air conditioning systems and industrial processes. "
Request for a quoteVITAL PARTS LTD
United Kingdom
Our High Temperature Tapes are perfect for all kinds of masking uses during processes which regularly use a lot of heat, examples of these processes includes Powder Coating where powder is sprayed on as a coating before being baked on to an application for a permanent finish. Coming in a huge number of variations including Ultra high temperature & Low tack adhesives, you can rest assured that we have the best choice for you. As mainly film based products, these High Temperature Tapes are malleable and flexible meaning that they can be used for tricky areas where there are many sharp corners.Discs are also available which can be used to seal off and prevent small holes such as screw holes from becoming filled during the coating process. For our full selection of Powder Coating Tapes / High Temperature Tapes please visit our website using the link below. Free sample lengths are available on all our tapes meaning you can try before you buy.
Request for a quoteCBG COMPOSITES GMBH
Germany
High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and solid parts or structural elements that can be used at temperatures up to 1.400 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% biosoluble — high temperature resistance — low thermal conductivity — high chemical resistance * — low weight — good tear resistance — high flexibility — easy processing — complicated geometries can be produced — recyclable * to achieve higher acid resistance, a special coating is required. Available from manufacturer. Application: Burner plant components, crucibles, thermocouple housings, coupling devices in continuous casting plants, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals, gasket in aluminium foundries, gaskets in blast furnaces, expansion joints, pipe insulation, catalyst insulation, repair work in the high temperature range.
Request for a quoteCBG COMPOSITES GMBH
Germany
High-temperature vacuum-formed products made from biosoluble ceramic fibres are lightweight and strong parts or structural elements that can be used at temperatures up to 1 .600 °C in air and in aggressive environments, including direct contact with liquid metals. — 100% natural — biosoluble — high thermal shock resistance — low thermal conductivity — high chemical resistance * — recyclable — low weight — good tear resistance — high flexibility — easy processing — harmless to health — complicated geometries can be produced * A special coating is required to achieve high acid resistance. Available from manufacturer. Fields of application: gaskets, crucibles, thermocouple housings, coupling devices in continuous casting plants, expansion joints, convex and flat gaskets in blast furnaces, channel elements of metal troughs, inlet device in the melting of non-ferrous and ferrous metals.
Request for a quoteGUANGZHOU WORLDE PACKAGING MACHINERY CO.,LTD
China
High-speed modified atmosphere packaging machine, high production efficiency, suitable for medium and large batch packaging. Greatly reduce the labor force and solve the problem of difficult recruitment. Thereby improving the product grade and saving labor costs.It is suitable for various specifications of trays, the mold can be customized and replaced, and one machine can be used for multiple purposes.Can be integrated with other supporting systems (such as automatic box drop, feeding, metal detection, weighing and labeling machine, etc.)Modified atmosphere packaging machine is widely used in: cooked meat, fruits and vegetables, pickled products, seafood, shellfish, fresh meat, poultry, bakery and other boxed food packaging. In locking the original nutrition and mouth of the food.At the same time, it prolongs the shelf life of goods.
Results for
High-temperature seals - Import exportNumber of results
25 ProductsCountries
Company type
Category