Results for
IGUS® GMBH
Germany
iglidur® sealing lip bearing d1 [mm]: Quick and easy-to-mount polymer bushing made of iglidur® J (JDSM) or iglidur® V400 (VDSM) with clip-on radial shaft seal ring as sealing for the rotating shaft. Seals off against dirt, dust as well as all pressure-less media. Polymer bushing with clip-on radial shaft seal ring Sealing for rotating shaft Temperature application range like iglidur® J Coefficient of friction only 10% higher than in iglidur® J Coefficients of friction identically exceptional like iglidur® J Reduced installation space as well as easy and simple mounting Realizable with numerous sealing types High-temperature option VDSM possible Temperatures till 150° C Material: iglidur® J High temperature option VATM, iglidur® V400 Seal ring made of fluorelastomer Bearing-sealing combinations for other applications on request When to use it? When the penetration of dirt and spray water should be prevented When only a small installation space is available in the axial direction When an existing seal should be integrated in a plain bearing When not to use it? When pressurized media should be sealed When absolute impermeability to the shaft and housing is needed continuously We'll gladly do the developing with you iglidur® sealing lip bearing d1 [mm]:
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
Motor shafts. Gear and frive unit shafts. Fan shafts. Clamping tools. Applications at high speed and lo pressure.
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
Applications at high speed and low pressure. With O‑ring as secondary seal for sealing in the groove base. Hygienic design without undercuts. No sump formation in front of the seal. Reduced heat buildup due to special lip design. Pressureactivated seal energization. The integrated wedge prevents the sealing lip turning inside out. Very long seal life due to high abrasion resistance. Material only generates low frictional force. Sealing lip does not stick to the mating surface even after prolonged shutdown
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
Types RWDR‑A, RWDRAS, RWDR‑B, RWDRBS, RWDR‑C, RWDRCS
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
The standard version is universally usable, but in special cases the light version can offer additional advantages. The light version is suitable for tight installation conditions and is also easier to fit in nonsplit grooves.This version reduces the friction. The low compression reserve with a negative effect on large tolerances must be considered.
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
With internally protected sealing lip. With O‑ring for sealing in the groove base. For high peripheral speed and increased chemical resistance
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
High pressures at relatively low speed. For fluids over a wide viscosity range and for gases. Rotary unions at high pressure. Robot axes
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
High termat or chemical specifications. Medium pressure and low speed. Suitable for almost all fluids. Robat axes, Rotary unions.
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
Types 231 to 238 are used for lubricating fluids and to a limited degree also for dry running and purely rotary or oscillating motion. They are only partly suitable for helical motion.
Request for a quoteIDG-DICHTUNGSTECHNIK GMBH
Germany
The standard version is universally usable, but in special cases the light version can offer additional advantages.The light version is suitable for tight installation conditions and is also easier to fit in nonsplit grooves.This version reduces the friction. The low compression reserve with a negative effect on large tolerances must be considered.
Request for a quoteFLUX-GERÄTE GMBH
Germany
Pre-assembled pump kit for 99,98 % drum emptying. Due to integrated backflow stop less than 0.05 l residual amount in 200 l drum possible. For pumping thin media out of 200 l drums (immersion length 1000 mm) or IBCs (mmersion length 1200 mm). Comprising drum pump F 425 with mechanical seal, outer tube in stainless steel, commutator motor F 460, hose, hand nozzle and compression gland. Can also be used in hazardous areas. Product attributes: - Pump with mechanical seal - Switch lever to close the backflow valve / foot valve - Pulsation-free transfer - Transfer against closed valve (e.g. hand nozzle) possible - Radial shaft sealing ring prevents intrusion of vapours and liquids into the coupling area Benefits: - Less than 0.05 l residual amount left in 200 l drum - Universally and flexibly applicable - Reduction of cleaning and waste disposal costs - Optimal use of fluids - No loss of medium when taking the pump from drum to drum
Request for a quoteGEPPERT RÜHRTECHNIK GMBH
Germany
The NRK series is a compact top-entry agitator that can be used to meet high requirements regarding both surfaces and cleaning inside and outside of the tank. Due to its’ compact design, agitator shafts with diameters of 25 mm and lengths of up to 1,200 mm can be realized, making the NRK the ideal mixer for small tanks in food and drug industry. GMP and FDA conform design. The NRK series agitator has an integrated bearing and coupling housing with flexible coupling to connect drives with shaft journals. The NRK can be supplied with radial shaft seal rings for non-pressurized operation or with liquid-lubricated mechanical seals on pressurized tanks. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3).
Request for a quoteGEPPERT RÜHRTECHNIK GMBH
Germany
NRK - Compact top-entry agitator The NRK series is a compact top-entry agitator that can be used to meet high requirements regarding both surfaces and cleaning inside and outside of the tank. Due to its’ compact design, agitator shafts with diameters of 25 mm and lengths of up to 1,200 mm can be realized, making the NRK the ideal mixer for small tanks in food and drug industry. GMP and FDA conform design. The NRK series agitator has an integrated bearing and coupling housing with flexible coupling to connect drives with shaft journals. The NRK can be supplied with radial shaft seal rings for non-pressurized operation or with liquid-lubricated mechanical seals on pressurized tanks. Explosion protection to ATEX 2014/34/EU for explosive zones 0 to 2 for gases and for explosive zones 20-22 for dusts (device group II, categories 1-3).
Request for a quotePROPACK DICHTUNGEN UND PACKUNGEN AG
Germany
Pre-Loaded Packing Ring in Metal Casing Characteristics WDR-rings are ready-to-fit sealing elements for shafts and axles The wide sealing surface offers extra protection against early wear on the shaft and as well on the seal WDR rings are located in the housing with interference fit. The sealing effect is facilitated through the pre-loaded encapsulated packing. Different packing styles can be utilized depending on application Housing Standard: St 1403 galvanized Special: e.g. VA (1.4301) - CrNi Standard Insert P1P Budget to +200 °C Main application Crank and drive shafts Guiding shafts Axles, spindles and similar equipment Sealing against fluid leakage and dust penetration Protection for bearings and drive units Suitable for All Industries to seal against fluid loss or protect against dust and dirt ingress. Variant Special variantes: A 22 up to +450 °C for high temperature application S 7/G up to +250 °C for applications in abrasive environment etc. The packing insert...
Request for a quotePROPACK DICHTUNGEN UND PACKUNGEN AG
Germany
Expanded natural Graphite in Purity 98 % – industrial grade or 99.85 % nuclear grade (chlorine content < 20 ppm) Temperature in steam Density min. 1.40 g/cm 3 Characteristics High cross section density Self lubrication and limited wear Dry running capability Coefficient of thermal expansion similar to steel Maintenance free and elastic, also under variable pressure Non ageing, high chemical resistance Attention! Precise tolerances and surfaces of application are requeste Operating range Pressure [p max]: 800 bar Temperature: t = -200… +550 °C pH: 0 - 14 Density: 1.80 g/cm³ Temperature in steam Density min. 1.40 g/cm 3 Main application Fittings Pumps (high temperature) Covers Valves Suitable for Valves and fittings of all Industries Approvals Oxygen BAM 200 °C/250 bar DVGW and KTW Variant Rings with integrated reinforcement or endcaps made from ANSI 316 Special quality TA Luft 300 with a leakage rate of 5.7 · 10 -3 mbar · l/(s·m) 300 °C Form of delivery ARF rings - endless,...
Request for a quoteTWK-ELEKTRONIK GMBH
Germany
Robust case with wall thickness of 5 mm either in seawater resistant aluminum or in stainless steel - shaft in stainless steel - rotating components with permanent magnet in front chamber - electronic circuit with ASiC and Hall elements and interface components fitted within main chamber, separated from rotating components by a metallic wall - integrated absolute multiturn gearbox for the acquisition of revolutions - optional potting against water jets (IP 69K) - electrical connections via round plug M12x1 or lead exit.
Request for a quoteDo you sell or make similar products?
Sign up to europages and have your products listed
TWK-ELEKTRONIK GMBH
Germany
Robust case with wall thickness of 5 mm either in seawater resistant aluminum or in stainless steel - shaft in stainless steel - rotating components with permanent magnet in front chamber - electronic circuit with ASiC and Hall elements and interface components fitted within main chamber, separated from rotating components by a metallic wall - integrated absolute multiturn gearbox for the acquisition of revolutions - optional potting against water jets (IP 69K) - electrical connections via round plug M12x1 or lead exit.
Request for a quoteTWK-ELEKTRONIK GMBH
Germany
Recording of the angular position and revolutions by means of Hall sensors - data output plus parameterisation and diagnosis via PROFINET. Robust housing manufactured from seawater-resistant aluminium or stainless steel - stainless steel shaft - ball bearing with radial shaft seal-sensor circuit consisting of ASIC with Hall elements - electrical connection via M12 connector or cable outlet. The Profinet interface according to IEC 61158 / 61784 or PNO specifications order No. 2.712 and 2.722, version 2.2, is integrated into the model series TRT absolute encoders. Real time classes 1 and 3 are supported, i.e. Real Time (RT) and Isochronous Real Time (IRT) plus the requirements of conformance class C. To achieve the SIL2 level, the TRT/S3 contains addtitional internal monitoring mechanisms as well as safe communication via PROFIsafe. The PROFIsafe protocol is implemented according to the PROFIisafe Profile for Safety Technologie version 2.4 (PNO Order No. 3.192)
Request for a quoteTWK-ELEKTRONIK GMBH
Germany
The incremental encoder with the model designation FOI records the angular position by means of a magnetic sensor and signal processing and generates the corresponding pulse outputs. The robust steel housing with anti-corrosion coating and stainless steel flange (AIMgSi1) ensures versatile use of the incremental encoder for your individual application. The shaft of the FOI is made of stainless steel and the bearings are equipped with a shaft sealing ring.
Request for a quoteTWK-ELEKTRONIK GMBH
Germany
Robust housing (wall thickness 5 mm) made of seawater resistant aluminium (AlMgSi1) or stainless steel (material: 1.4305 optional 1.4404) - Redundant power supply as well as sensors and electronics - Common shaft (measuring axis) with ball bearing, shaft sealing ring and permanent magnets in prechamber - Sensor circuit consisting of ASICs with Hall elements and interface electronics in closed main chamber - The contactless electromagnetic sensor systems are extended by a 12-bit D/A converter so that the measured variable is available as an analog signal from 0 (4) to 20 mA or 0 to 10 VDC - Electrical connections via connector M12x1.
Request for a quoteResults for
Shaft seal rings - Import exportNumber of results
23 ProductsCountries