Blocks of cement - Import export

COMPOSITION AND APPEARANCE Plaster-based powder filler, special cements, calcium carbonate, resin, cellulose fibre and various admixtures. The compound obtained is white in colour. TECHNICAL CHARACTERISTICS • Setting time : 30 to 40 minutes • Hardening time : 1 to 2 hours. • Second coating : after 3 hours • Adherence : complies with NFT 30 608 SUITABLE SURFACES All types of interior surfaces complies with DTU 59.1 : plaster, plasterboard, plaster blocks, concrete, cement coating, breeze blocks, cellular concrete, bricks, ceramic, old paintwork, old painted fibreglass, floor tiles, wall tiles, etc. COVERINGS After the filler has completely dried, it can be covered using all types of paints, plaster-based coatings, paste coatings, wallpaper paste. PREPARATION OF SURFACES Surfaces must comply with standard DTU 59.1 and be clean, dry and free from dust and any trace of separating agent. Correctly open up, bevel and dust off the cracks.

TECHNICAL DETAILS Interior ready-to-use smooth finish coating, easy to apply - requires less sanding down than a traditional coating and therefore creates less dust. Apply with spatula, then sand down. Less dust is created, and the dust is less volatile. SUITABLE SURFACES Interior walls and ceiling : plasterboards, gypsum blocks, concrete, cement coating, aerated concrete, sealants. REFERENCE DOCUMENTS DTU 59.1. PACK SIZE 25 kg bucket. AFNOR NFT 36.005 AMOUNT REQUIRED From 0.6 to 1 kg/m² depending on quality of surface. DRYING TIME 6 to 24 hours depending on conditions and quantity applied. RECOMMENDED APPLICATION To avoid all traces of filler, finish with a slightly rounded action.

DESCRIPTION Coating to quickly fill all sizes of cracks, holes and grooves with no shrinkage and no cracking. COMPOSITION AND APPEARANCE Plaster-based powder filler, calcium carbonate, mineral reducer, cellulose derivatives and various admixtures. The compound obtained is white in colour. SUITABLE SURFACES All types of internal unfinished or painted surfaces : plaster, plasterboard, plaster blocks, concrete, cement coating, breeze blocks, cellular concrete, bricks, terracotta... TECHNICAL CHARACTERISTICS • pH: neutral • Setting time : 30 minutes depending on the ambient conditions and the thickness applied PACKAGING 5 kg and 15 kg bags. APPLICATION To be applied using a coating knife. Amount required : 1 kg m²/mm thickness. DRYING TIME Depends on the ambient conditions, the nature of the surface and the thickness of application. Generally speaking, when spread to a thickness of one cm, the filler dries in 6 hours.

TECHNICAL DEFINITION Multi-purpose filler for interior use. • Filling holes, cracks, chases • Fixing and bedding • Pasting polystyrene, roses, cornices • Finishing COMPOSITION AND APPEARANCE Powder filler composed of plaster, calcium carbonate, resin, cellulose fibre and various additives. Produces a white paste. ACCEPTED SUBSTRATES All types of interior substrates: plaster, plasterboards, plaster blocks, concrete, cement rendering,concrete blocks, aerated concrete, brick, earthenware, TECHNICAL CHARACTERISTICS • Grain size : fine • Adhesion : complies with standard NFT 30 608 • pH : neutral • Setting starts after 50 minutes • Setting ends in 1 hr 10 min • Bending : 3 N/mm2 • Compression : 7 N/mm 12 kg buckets on wrapped pallet. STORAGE 9 months in original unopened packing protected from damp. THE TEMPERATURE DURING APPLICATION AND DRYING MUST BE SUPERIOR TO 5°C. DO NOT USE ON A DAMP SUBSTRATE. DO NOT USE ONCE THE PASTE HAS STARTED TO SET.

TECHNICAL DEFINITION Ready-to-use surface filler paste for filling interior holes and cracks. COMPOSITION AND APPEARANCE Water, calcium carbonate, sand, resin and various additives. SUITABLE SUBSTRATES All types of interior substrates : concrete, cellular concrete, cement, breeze block, brick, plasterboard, plaster tiles, plaster, old paint. COVERING Primer coat, smooth surface filler, wall coverings, paint REFERENCE DOCUMENTS • Filler meets EN 16566 standard • DTU 59.1 : Paint work TECHNICAL CHARACTERISTICS • Density : 1.5 • Dry extract : 82 % STORAGE 9 months in original unopened packaging away from frost and high temperatures. PREPARATION OF SUBSTRATES Substrates must comply with the DTU 59.1 standard i.e. be dry, clean, dust-free, hard and free of any trace of separating agent. APPLICATION Applied by hand using a filling knife or spatula. The thickness is 2 cm; to fill deeper holes, build up the filler in several steps The maximum thickness will be 1 cm per coat.

TECHNICAL DEFINITION Ready-to-use coating paste for smoothing irregular surfaces on interior and exterior walls. Particularly suitable for damp areas. COMPOSITION AND APPEARANCE Emulsion resin, calcium carbonate, water, rheological agent and various additives. The paste is off-white in colour. SUITABLE SURFACES • Plasterboard panels • Plaster blocks • Ceramic tiles • Concrete • Cement coating • Rpe • Old paint • Glass web fabric • Sanded and printed wood SUITABLE SURFACES Plaster-based top coat. Paste coating. Matte paint. TECHNICAL CHARACTERISTICS • Granulometry : up to 0.6 mm • Adherence : complies with NFT 30 608 • pH : neutral • Dry extract : 80% STORAGE 6 months in unopened original packaging, away from frost and extreme heat. CLASSIFICATION AFNOR NFT 36.005. FAMILY IV - CLASS 4 B. COMPLIES WITH DTU 42.1. PREPARATION OF SURFACES Surfaces must comply with standard DTU 59.1, and be clean, dry and free from dust and any trace of separating agent.

TECHNICAL DEFINITION Extra-fine finishing filler in powder form for all types of interior jobs. The substrate is now ready to be decorated with paint, wallpaper or any wall covering. COMPOSITION AND APPEARANCE Calcium carbonate, redispersible resin, rheological agent and various additives. Produces a white paste. SUITABLE SURFACES • Wallpaper • paint • wall covering • Plasterboards • Concrete • Old paint • Plaster-based high build filler • Plaster blocks • Cement render • Undercoat TECHNICAL CHARACTERISTICS • Setting time : >24hrs (drying filler) • Powder’s density : 0.8 • Grain size : very fine • pH : 7 • Adhesion : complies with standard NFT 30 608 MIXING FACTOR Use approximately 11-12 litres of water for one 25 kg bag. Allow the paste to rest for 15 min before use. APPLICATION Apply either manually with a steel trowel or a putty knife, or mechanically. Allow to harden and scrape off any possible imperfection before sanding down.