Syntech HAG Pompa AZ-PT/B : 40 bar manual pump for masonry injections of resins
Syntech HAG Pompa AZ-PT/B : 40 bar manual pump for masonry injections of resinsSyntech HAG Pompa AZ-PT/B : 40 bar manual pump for masonry injections of resinsSyntech HAG Pompa AZ-PT/B : 40 bar manual pump for masonry injections of resins

Syntech HAG Pompa AZ-PT/B : 40 bar manual pump for masonry injections of resins

Syntech HAG Pompa AZ-PT/B Manual single-piston pump, self priming, simple effect, to inject polyurethane and epoxy fluid resins. The maximum pressure that can be delivered by the pump is 40 bar. The flow rate is 1 litre in 55 cycles. The pump AZ-PT/B has a bulk at the base of maximum 65x110 cm, and is equipped with an extensible telescopic stand, in order to adjust the height as a function of the ergonomic requirements of the operator who uses it. The height from the ground varies from 85 cm to 125 cm. Masonry injections of hydro-expansive polyurethane resins for stopping water infiltration and/or fluid epoxy resins for masonry reinforcement. Install the injectors SYNTECH H.A.G. INIETTORE 120 and SYNTECH H.A.G. INIETTORE 170, as specified in the respective technical data sheets. Connect the high-pressure hose supplied with the pump to the special injector, which is suitably installed in the masonry. Immerse the suction pipe supplied with the pump (reinforced plastic pipe) in the container (bucket, bottle, etc. ) containing the resin to be injected. Insert the pressure relieving tube (transparent plastic tube) in the same container. Start the injection operations, by pumping the resin in the injectors by activating the pumping lever. Upon saturation of the cavity to be injected, the pressure of the injected liquid will be such as to impede the operation of the lever; at that point it will be necessary to totally relieve the pressure by operating the appropriate vent cock. Disconnect the hose from the injector used and connect it to a new injector. Repeat the procedure for each intended injector. At the end of each injection operation and before storing the pump, it is strongly recommended that you clean it carefully by first circulating Nitro thinner in the hydraulic circuit for a few minutes, and then by circulating the specific lubricant cleaner SYNTECH H.A.G. CLEANER. Product to buy as needed. Bulk material 1 unit
Similar products
1/15
Syntech HAG Iniettore : "Flat head" injectors in steel and rubber for masonry injections
Syntech HAG Iniettore : "Flat head" injectors in steel and rubber for masonry injections
Syntech HAG Iniettore This rubber and steel injectors are to be inserted in line with the damage, cracks, loose foundations, joints, cavities and so ...
IT-46044 Goito
Fluid SRA: Hydraulic shrinkage reduction additive for mortars
Fluid SRA: Hydraulic shrinkage reduction additive for mortars
Fluid SRA Concentrated liquid additive formulated to reduce shrinkage in the plastic phases of cement mortar. It reduces shrinkage by over 50% compar...
IT-46044 Goito
Syntech Primer EP-W : Solvent-free two-component epoxy primer for cement surfaces
Syntech Primer EP-W : Solvent-free two-component epoxy primer for cement surfaces
Syntech Primer EP-W Syntech Primer EP-W is a solvent-free two-component epoxy resin to be used as a bonding primer for applying all epoxy cycles on c...
IT-46044 Goito
Syntech Poliurea Spray - FL : Elastomeric system in polyurea specific for vehicle paving
Syntech Poliurea Spray - FL : Elastomeric system in polyurea specific for vehicle paving
Syntech Poliurea Spray - FL Syntech Poliurea Spray - FL is a pure polyurea designed for the specific application on driveways and parking lots in gen...
IT-46044 Goito
Repar Tix G2 : Thixotropic slightly expansionary mortar, for anchoring and underpinning
Repar Tix G2 : Thixotropic slightly expansionary mortar, for anchoring and underpinning
Repar Tix G2 Thixotropic, reinforced fibre, anti-shrink mortar, slightly expansive in plastic phase, high-performance in terms of resistance and wate...
IT-46044 Goito
Osmocem 447 : Cement Mortar anti-leaching waterproof, for quick repairs
Osmocem 447 : Cement Mortar anti-leaching waterproof, for quick repairs
Osmocem 447 Anti-leaching mortar with plastic consistency, fast-hardening, based on silica fume, high resistance hydraulic binders, polymeric binders...
IT-46044 Goito
Repar Tix GS : Rheoplastic, structural thixotropic cement mortar for extensive thicknesses
Repar Tix GS : Rheoplastic, structural thixotropic cement mortar for extensive thicknesses
Repar Tix GS A structural and shrinkage-compensated thixotropic cementitious mortar with a maximum aggregate grain size of 5 mm, consisting of high-s...
IT-46044 Goito
Syntech AS 21 : Thixotropic epoxy filler, for repairs, fixings and beton plaque
Syntech AS 21 : Thixotropic epoxy filler, for repairs, fixings and beton plaque
Syntech AS 21 Two-component structural adhesive epoxy filler, with soft consistency, thixotropic, easy to spread (malleable paste), for the anchorage...
IT-46044 Goito
Syntech HAG Eco : Hydro-expansive polyurethane resin, without solvents, injectable
Syntech HAG Eco : Hydro-expansive polyurethane resin, without solvents, injectable
Syntech HAG Eco Mono-component, enabled for contact with drinking water, semi-flexible, expanding (increases its initial volume of about 20 times) po...
IT-46044 Goito
Syntech HAG Mono : Low viscosity hydro-expansive single-component polyurethane resin
Syntech HAG Mono : Low viscosity hydro-expansive single-component polyurethane resin
Syntech HAG Mono Single-component hydro-expansive polyurethane resin (does not require a catalyst and increases its initial volume by approximately 3...
IT-46044 Goito
Syntech IC 55 : Fluid epoxy resin for reinforcing building structures
Syntech IC 55 : Fluid epoxy resin for reinforcing building structures
Syntech IC 55 A two-component pure epoxy adhesive that is fluid with a low viscosity, free from fillers and solvents, being specific for high perform...
IT-46044 Goito
Syntech HAG Flex : Hydro-expansive, flexible, injectable polyurethane resin, without solvents
Syntech HAG Flex : Hydro-expansive, flexible, injectable polyurethane resin, without solvents
Syntech HAG Flex Mono-component semi-flexible, expanding (increases its initial volume of about 10 times) polyurethane resin, free from solvents, per...
IT-46044 Goito
Protech Oxicrom : Ferrous oxide compound for concrete, plaster and paint pigmentation
Protech Oxicrom : Ferrous oxide compound for concrete, plaster and paint pigmentation
Protech Oxicrom Protech Oxicrom is an inorganic oxide/hydroxide based powder compound. Added in appropriate quantities and homogeneously distributed,...
IT-46044 Goito
Syntech AS 31 : Thixotropic epoxy putty for structural fixes and repairs
Syntech AS 31 : Thixotropic epoxy putty for structural fixes and repairs
Syntech AS 31 The two-component structural epoxy adhesive putty is soft, thixotropic and spatulable (malleable paste), ideal for anchoring steel conn...
IT-46044 Goito
Osmocem Flex : Plasto-elastic waterproofing cement for terraces and masonry
Osmocem Flex : Plasto-elastic waterproofing cement for terraces and masonry
Osmocem Flex A two-component osmotic cementitious waterproofing agent in water dispersion, being a modified polymer that is highly flexible and defo...
IT-46044 Goito

The europages app is here!

Use our improved supplier search or create inquiries on the go with the new europages app.

Download in the App Store

App StoreGoogle Play