galvanized steel Italy

... steel to annealed and galvanized wire, highstrength steels such as stainless steel, springs steel and nonferrous wires such as brass, bronze, copper and aluminum using special equipment. The wide range of accessories allows you to customize the machine to the different needs of the industrial market. Available versions RI 8/ML The manual setting of the mechanical lengthstop will enable processing wires with a bar length accuracy of ±0,1 mm. This newly designed contactless lengthstop enables to action the cut without the conventional...

...Spiral tubes are made from galvanized stainless steel or copper strip wound in a spiral with continuous helical stitching for a tight seal. The external raised stitching gives the pipes significant rigidity and crush resistance, three times greater than that of a traditional rolled tube. Tubes can be produced starting from a minimum diameter of Ø 80 mm, up to a maximum Ø of 1400 mm. Our spiral tubes have been used for the foundations of the C metro line in Rome, where concrete is poured into the tube, allowing the construction rebar to pass through inside.

...The Swing Carousel consists of a rotating structure rising along a central column and supporting two rows of swinging chairs for accommodation of 1 passenger each. Double seats is also possible, to accommodate one adult and one child. All decorative panels are made out of fibreglass/alluminium with galvanized-steel frame. All decoration are hand made and all painting one by one hand-brush...

... perfectly dry surfaces. Preliminary construction of specific anchoring scratch coats, breathable, made with Untersana. The rendering, applied by "spraying", must provide a rough, corrugated surface, designed to promote the bonding of the subsequent plaster, which must be applied no later than 2-3 days. In the case of wooden surfaces, attach a galvanized steel wire mesh, diameter 2 mm and mesh 5x5 cm...

... galvanized sheet; > plastic-coated galvanized sheet. Standard skin thickness 5/10 mm. Joint between panels: standard dry MF. The insulating core made of extruded polystyrene offers a range of advantages: > high mechanical resistance (up to 3 times higher); > zero absorption of water or vapor by the insulation; > high thermal insulation capacity; > non-propagation of flame (thermosensitive material).

...Italgomma2 is a company where both large multinationals and small businesses can benefit from the support of a strong and competent team. Our company is also pleased to offer a wide range of ready-to-deliver products, including: stainless steel, plastic, or galvanized clamps, Teflon rolls, Seaflon™ seals, cleaning products, and technical maintenance supplies for systems such as: Saratoga, Pattex, Datacol, anti-vibration products, and stainless steel and rubber compensating joints.

... and threaded rods. - Highly flexible plug, with numerous accessories available in galvanized steel and stainless steel (A2 - A4). - Reduced outer diameter. - Available in an intrusion-proof version with a permanent AF nut and a breakaway hexagonal head nut in stainless steel. - Available in a through version for the object to be fixed.

...Tree grate made in galvanized and powder coated steel. Available in various sizes and designs, the possibility of having combined vertical protection. http://ecommerce.flysrl.com/categoria/arredo-urbano/griglia-salvapiante/...

...Finned armored resistors are constructed using the traditional yet effective technology of insulated stainless steel tubing with magnesium oxide (MgO). Our products are available in diameters of 6.5mm and 8.5mm and can be manufactured according to customer specifications. The fins can be of two types: - Circular fins in AISI-304 with a height of 5mm and variable fin spacing - Rectangular fins measuring 50x25mm in galvanized aluminum (if stamped) or in AISI-304 (if welded)...

...Flexible cable, made of galvanized steel coated with BLUE PVC, with a flexible probe, rings, and male M12 connector. Cable diameter 8 mm. Available in various lengths.

...Gamma benches with and without backrest. Made of hot-dip galvanized steel, powder-coated with polyester resin, supplied partially disassembled, in kit form. Sides available in two RAL colors: 7016 / 9006 Seat/backrest available in three RAL colors: 7016 / 9006 / 8023...

...{"a":"Robust carrier structure made of aluminum","b":"Transportable by truck or on a standard car trailer up to 2.5 tons.","c":"Platforms and stairs for access made of aluminum and removable from the structure.","d":"Floor made of stainless steel sheet with non-slip adhesive strips","e":"Shower basin made of galvanized stainless steel","f":"Partition walls made of insulating aluminum sandwich...

...LIVING CONTAINER CONTAINEX WALLS MADE OF REPLACEABLE AND RECONFIGURABLE GALVANIZED SHEET PANELS EXCELLENT INSULATION AND ACOUSTIC BARRIER ROBUST STEEL FRAME WITH ANGLES FOR PREFABRICATED STRUCTURES AND FORKS FOR FORKLIFTS. STACKABLE UP TO THREE STORIES. STANDARD EXTERNAL RAL COLOR 9010 WHITE - 5010 GENTIAN BLUE OPTIONAL: RAL OF CUSTOMER'S CHOICE INTERNAL COATING RAL 9010 OR ALTERNATIVELY...

...Outdoor bench with backrest and armrests, made entirely of galvanized and painted steel. Upon request, it can be made of stainless steel. http://heliosarredourbano.com/...

...It is the exclusive patented GI.ON Big Bag Frame designed to optimize the use of big bags in everyday applications. Constructed from galvanized steel, weighing approximately 50.59 kg, it is suitable for holding big bags up to 1500 kg. It allows for easy loading, storage, and unloading of materials (granular, cement, feed, etc.), as well as inert materials, debris, and waste contained within the bags.

...All standard tecno azzurra machines are ce marked and ready for use. Standard configuration: extractor with anti-sparking safety system atex lighting main structure formed by self-supporting galvanized panels with non-cutting edges filter clogging detection system lv control panel wired with flame-retardant cable type of filter installed according to machine model all our machines can be manufactured, either fully or partly, from aisi 304/316 stainless steel...

...MATERIAL GALVANIZED STEEL DIMENSIONS GA003/A L76XP54XH61 CM GA003/B L87XP58XH67 CM GA003/C L107XP68XH75 CM GA003/D L118XP78XH85 CM...

...Covers made of stainless steel, galvanized sheet metal, aluminum, special alloys, etc.

...Single-phase or three-phase electric motor, adjustable or fixed height blade Blade diameter of Ø 315 mm. The innovation in this model comes from the flat belt transmission, which allows for 110 mm of useful cutting, reduced friction, and therefore a greater starting torque. Structure made of pre-galvanized and painted steel sheet, with tool holder and document holder.

... mass-coloured or especially made panels. Examples of anchoring systems However the material that is more frequently used is polymethyl methacrylate for its clear and quick-handling features. The TECNOWALL clear panel is fixed to the bearing structure by a suitable frame hot-galvanized steel and painted frame; the sheet is surrounded by a rubber seal that is resistant to weathering agents, shaped so as to follow thermal-expansion-induced movements of the sheets. The polymethyl methacrylate sheets used can be hot- and cold-thermoformed so as to take on the shapes as requested by Customer or su...

The production of Tecno Ruote includes wheels made of rubber, nylon, polyurethane, cast iron, and aluminum designed to meet all market segments. The range of rubber wheels encompasses a wide variety of diameters, within which we can find an application for every need, naturally supported by the great availability of mounts with various types of attachments. Nylon and nylon-polyurethane wheels can be applied not only to galvanized mounts but also to those made of stainless steel, essential for trolleys and machines used in healthcare and food industries.

... currently on the market. Over the years, the company has developed its own identity, grown in the market, and acquired a 10,000 m² plot of land where it established its operations. Comfer is involved in the processing, transformation, and distribution of iron and metal articles for the steel and iron industries in Central-Northern Italy. The company boasts a large and well-stocked warehouse with metal...

EUROTUBI produces galvanized, hot-rolled pickled, and cold-rolled welded round tubes in mild carbon steel with large diameters and thin wall thickness. The tubes are manufactured by continuous forming tube mills using cold-rolled, hot-rolled pickled, and galvanized steel strips. EUROTUBI’s entire production is managed and supported by the Technical Department, starting from the analysis of...

The company Giama operates in the metal carpentry sector, specializing in the processing of stainless steel, iron, aluminum, reinforced concrete iron, galvanized sheets, welded wire mesh, metal nets, iron beams, tubulars, and metals in general, as well as precision mechanical processing. Do not hesitate to contact us for any information or needs. Giama is located at Via delle Industrie, 19 in Poggio Torriana - Poggio Berni (RN).

Since 1987, Olsar Srl has been engaged in sheet metal processing using laser cutting, stamping, shearing, bending, paneling, welding, and assembly of stainless steel, galvanized sheet, pre-painted, pickled, polished, and unismalt materials. Our facilities, located in Arsego di San Giorgio delle Pertiche (Padua), cover a total area of 14,000 square meters of covered space. We support our clients...

TECNOMA, FOUNDED IN 1994, SPECIALIZES IN THE DESIGN AND MANUFACTURE OF PROFILING LINES, FROM COIL TO FINISHED PRODUCT. OUR RANGE OF LINES INCLUDES: 1- Compact profiling lines, fixed, cassette-type, adjustable duplex width, multi-profile, and combined. 2- Lines for machining metal sheets (galvanized steel, pre-painted steel, stainless steel, aluminum, copper). 3- Lines for the production of all...

...It is a service center for rolled products in quality FF360, FF430, and FF510. It offers custom cutting for: commercial rolled products in standard bars, HE IPE UNP INP tubes S/S, conduit AD-PE UUNI 7863, mechanical E355 EN 10297, structural tubes quality S 355J2H; galvanized and raw gratings; galvanized steps and pedestrian walkways; expanded and micro-expanded sheets, perforated in carbon steel; stainless steel AISI profiles and sheets; drawn A37, rolled and ground C40; black and galvanized welded wire mesh; aluminum sheets and profiles; iron items for gates, stairs, doors, windows, and fences.

The company Bal.Fer specializes in the trade of metal scrap and industrial demolitions. We purchase ferrous and non-ferrous scrap at market prices; we have loading availability with specific equipment; trucks with cranes and roll-off containers. We are equipped for the collection of various materials: ferrous scrap, metal scrap, waste paper, rags, plastic, glass, and more. We also offer fencing nets of all types, galvanized sheets, flat and corrugated sheets, and metal boxes.

We are a company based in Treviso that has been specializing for over 15 years in the construction of windbreak nets and agricultural coverings. The Agricultural Tunnels offered by MPS are sturdy structures made of galvanized steel tubing. They are ideal for farms or industries that need storage for protecting animals, for housing forage, or agricultural tools. We are capable of creating any type of PVC covering.

SIKA specializes in cold profiling and sheet metal processing to create various types of profiles based on customer designs. Sika manufactures profiles, steel profiles, and metal profiles of any type and material (stainless steel profiles, copper, bronze, painted steel, galvanized steel, pickled steel, aluzinc, zinc-magnesium, Cor-ten steel, etc.). From the simplest sections to the most complex...