components passive Germany

...Cores made from various specialty powder alloys (Manufacturer CSC) Cores made from different specialty powder alloys (from manufacturer CSC, Korea) Permeabilities of approximately 50µ - 250µ @10kHz, very low-loss variants, various shapes possible, including custom components, potting of cores is also possible!

...Passive Components Perfect for miniaturization in EMC applications Wide impedance coverage from 10 to 300 Ohms Operating temperature: -55°C to +125°C Applications: General signal & low power lines Audio / Video / Clock signal lines Small mobile devices...

... Another serious issue is the operation in conditions of extreme heat, and there are situations where placement in a cooling liquid is the only way. Certain high voltage applications may require the immersion of all components in insulation oil, such as MIDEL. Quite a few cooling or insulation oils behave aggressively towards metallized polypropylene, causing swelling of the film and deterioration of the contact layers. They must therefore be kept away from the capacitor elements. In the past, mostly MKV capacitors (with oil-impregnated paper electrodes) had to be used in such situations.

... experience. A smooth process is ensured by the support of a dedicated contact person from the inquiry to the project handover. Here are the individual focus areas: - Front and rear center armrests - Headrests (active, passive, and ventilated) - Cupholders - Seat armrests...

SRT Resistor Technology GmbH was founded in 1996 through a management buyout of the resistor product division of Siegert GmbH. While Siegert had specialized in miniature resistors for hearing aids for several decades, SRT has achieved a leading position in the global market with high-ohm resistors over the last ten years. The main applications for these resistors are in the fields of industrial el...

We manufacture, trade, and mediate products for the automotive supplier industry, electronics industry, coating industry, and other sectors. Our suppliers come from Germany, Austria, England, Spain, China, and Taiwan. We deliver our products quickly and cost-effectively from a batch size of ONE for your development and production start. For your series production, we supply large quantities at l...

...Manufacturing of LTCC (Low-Temperature Co-fired Ceramics) substrates with outstanding properties for thermal management, integrated passive components, and 3-dimensional design.

...["Booster","Services","Introduction systems for cables / lines","Installation materials for data technology","ISDN distributor","Media converter","Modem","Module for active network component","Multiplexer","Network hub","Network management software","Network repeater","Network router","Network switch","Network adapter","Passive adjustment adapter","PC cable","Print server","Interface converter","USB hub","Wireless antenna","WLAN access point","WLAN network adapter","Accessories for active network components"]...

Rod core chokes according to customer specifications with wire thickness from 0.3 to 3.5 mm - standing/lying - single/dual layer - bent/straight connections - chamfered wire ends, dip-tinned without drops - DIN EN ISO 9001 2008.

EMA-TEC GmbH is a manufacturer of induction heating systems. It was re-established in 1998 by engineers from the bankrupt company Inducal Göllingen.

... working area and collect the finished product. The VersaGlue processes optoelectronic elements like VCSELs, photo diodes, laser dies and micro optics with highest precision while the passive placement of fiber ribbon cables is another major application.Thorough design and continuous optimization of all functional groups lead to superior mechanical stability. Mechanical references with tight tolerances provide a repeatable manufacturing operation from device to device.

...Ensure protection against warranty claims with the Hanno 3-Level Joint Sealing System: By using Hanno system components for all levels, a project-specific functional warranty of 15 years is possible. Impress your customers with the prospect of reduced heating costs and a long-term guarantee of joint quality. With the Hanno 3-Level Joint Sealing System, you achieve a tested* passive house-compatible joint sealing for your windows.

... suitable for passive isolation of measuring and testing machines, individual building components, up to entire buildings (earthquake protection). Specifications Load capacity FCd per spring package: 0.07 kN to 20.11 kN Natural frequency ne vertical: 2.6 Hz to 4.2 Hz Isolation efficiency up to 90% Amplitude damping made of plastic or viscous mass Optional height leveling With and without preloading Additional Features The ISOFED steel compression spring program is characterized by its versatile modular system.

... your specifications, thus perfectly integrated into your application. The basis for this is existing platforms... www.ipc-core. Display diagonal: from 5" to 24" Display brightness: 500cd/m2 Touch technology: Capacitive Processor: NXP i.MX Cooling: Passive Operating voltage: 10V to 32V DC Operating system: Linux Additional: Chromium, HTML5 Webclient...

... finding the following components: - Active components - Passive components - Resistors - Capacitors - Electromechanical components - Heat sinks - Connectors - Other components - CCFL lamps and inverters - Machined parts - Heating cartridges - Sensors/temperature measurement technology - Thermal interface materials Do you have questions about sourcing specific components? Don’t hesitate to contact us!

...The standard carrier tape is used for the secure packaging (strapping) of surface-mounted components. By strapping components, they can be easily and effectively processed by automatic pick & place machines. The carrier tape is suitable for EGB components and for passive components such as springs, sheets, etc. For the packaging of DIEs, we offer a special carrier tape characterized by a sharp...

...In all standard and special materials. Single and double-sided assembly. Multilayer PCBs With up to 48 layers for accommodating active and passive components for the miniaturization of your assemblies. PCB Size All shapes and types up to 1250 x 500 mm.

... goods and magnetic coils for all demands of everyday technology. In standard operations, as well as under special stress, the assemblies produced with dedication and care are reliable components of electronic and electrotechnical assemblies.

As a medium-sized family-run business, BLINZINGER ELEKTRONIK GMBH has been involved in the development and manufacturing of electronic products for the industry since 1986. Our product range includes technical ceramics such as soft magnetic ferrite cores and their processing, magnetic components like transformers, chokes, couplers, as well as other winding goods and assemblies, up to complete...

.../2023 fiscal year. The foundation for continuous growth lies in over 113 years of experience, the highest quality standards, and a consistent global orientation towards customers and markets. The company in numbers: - around 2,400 employees worldwide - of which more than 120 employees in development/design and quality assurance - more than 150 apprentices - our portfolio includes over 4,000 devices and components - sales take place in 70 countries through our partners as well as - 19 foreign subsidiaries and own offices...

... supplies both speed•pipe® microducts and duct assemblies for the use of existing infrastructure as well as for the establishment of new passive infrastructures, along with connection, sealing, and fixing elements and repair kits. Additionally, the product portfolio has recently been expanded to include fiber management systems. You receive all components of complete microduct systems from a single source. All individual system components are compatible with each other, allowing for a wide range of combinations for all application areas. All fittings are separable, reusable, and gas- and water-tight.

... offers piezoelectric shakers and shock wave generators. The product line of piezo composites opens up new applications in the areas of: - Material testing - Testing technology - Shock generators - Vibration excitation - Shaker vibration damping - Highest dynamics - Extended temperature range through highly efficient passive cooling.

... construction of special machines tailored to customer needs, with a highly qualified team of designers and skilled workers who provide complex solutions for assembly and testing machines, stamping and tool systems, packaging and palletizing modules, as well as special automation for electronic components. From design using state-of-the-art 3-D CAD software to individual production with flexible CNC machines...

For 40 years, we have been your reliable partner for SMT equipment. Here at our production site in the picturesque Kastl/Utzenhofen, motivated employees work on modern machines to provide you not only with a comprehensive series program but also with customized special solutions.

DESK Elektronik System Komponenten GmbH designs, constructs, and manufactures electromechanics for all areas of electronics and electrical engineering in Eppertshausen, in the district of Darmstadt Dieburg. Whether you are purchasing a product from the fields of electromechanics, "NIM-CAMAC", or "Telco Systems", you can always be assured of receiving a high-quality product, manufactured with mode...

Manufacturing of SMD laboratory assortments (standard program and custom designs) and distribution of SMD components (mainly passive) in sample, small, and production quantities.

Distributor of active, passive, and electromechanical components in Europe.

Manufacturer of Products for Passive Fire Protection With over 100 years of experience in the development and production of components and systems for preventive fire protection, AIK Flammadur Brandschutz GmbH is a trusted partner by your side. Our versatile portfolio and innovative solutions for individual challenges guarantee you optimal fire protection. Since June 2016, AIK has been part of...

Development and production of electromechanical assemblies and high-precision plastic parts. Key technologies include highly economical assembly solutions with semi-automatic and fully automatic assembly lines, as well as plastic injection molding systems.