sensor measuring equipment Germany

...Pressure sensor for analogue filling level measurement Supply voltage 24 V DC Output of an analogue measuring signal 4 – 20 mA Pressure ranges depending on tank height 0 – 50 / 200 or 400 mbar Safe at several times over-pressure Explosion protection according to ATEX ...

...Aluminium base Standard column of our VMM150 measuring microscope Z axis with 150 mm travel range...

...Thermo Sensors are needed in any controlled heating process. For various applications different types of thermocouples are obtainable. Most common are thermocouples (TC) and resistance sensors (RS). Both types are available in the same executions as a matter of princible. For non-contact measuring infrared sensors are the rights choice, either in stationary executions or as portable measuring instrument.

... medical equipment, the food stuffs industry etc. The sensor can additionally be fixed by means of the two mounting lugs to ensure a tight fit on the tube. Caution The switch point is factory pre-set so as to lie exactly between the two mounting clips. When readjusting the switch point, please observe that it again lies between the two clips. A mass surface in the proximity (< 10 mm) may influence the switch point and may necessitate a readjustment.

...The HICPRO is the ultimate portable device for measuring HIC values (Head Injury Criterion). All the necessary measurement technology and IT equipment required for determining the head injury factor is included in the device. The collected data can be displayed directly on the device or transmitted via WiFi or USB to a PC, tablet, or smartphone. The device can be easily used to check the safety...

... requirements for exact measurement with excellent long term stability. Features — nominal pressure: 0 ... 1 mH2O up to 0 ... 250 mH2O — accuracy: 0.25 % FSO — output signal: RS485 with Modbus RTU protocol — diameter diameter 26.5 mm — small thermal effect small thermal effect — high accuracy excellent accuracy — reset function Optional Features — drinking water certificate according to DVGW and KTW — different kinds of cables — different kinds of seal materials Housing material:stainless steel Signal output:Digital - Modbus RTU/RS485 measuring cell:stainless steel...

...Used to correct the tension factor of a drive, thus assisting the user in maintaining optimal belt tension. This device operates on the principle of frequency measurement. Features - Non-contact measurement with repeatability - Wide measurement range from 10 Hz to 600 Hz - High accuracy - Evaluation of measurement result quality - Suppression of background noise - Universal measuring head for comfortable measurement - Removable measuring sensor for tight spaces...

... ... Package includes: — Oxygen analyser — Power cable — Hose set, 3 m, incl. filter and probe — Calibration certificate — Transport case Measuring range:5ppm - 21% O2 Ambient temperature:0–45° C Measuring accuracy:+/- 0.3mV (EMK sensor) Heat-up time:3–5 min Response time:approx. 2 sec. for changes Dimensions (L x W x H):180 x 210 x 85mm without handle Mains voltage:100-240V AC Heating cycle load:approx. 40VA Standard load:approx. 20VA Weight:2.1kg...

...CoriSENS is a rotation rate sensor for measuring angular velocity ω. It detects rotational movements using a MEMS gyroscope. This measuring signal in a range of ± 20° / s is converted by the sensor electronics and transmittes an analog current signal as well as voltage signal in addition. The sensor is certified according to uniform standards for electronic equipment on rail vehicles (DIN EN 50155) and can be operated directly with the usual onboard supply (24 V). Supply voltage:24 V Sensitivity:100 mV/°/s & 0,4 mA/°/s Measuring range [°/s]:± 20...

...Low-noise coaxial measuring cables are used wherever the smallest voltages or charges have to be reliably measured, e.g. in pH measurement technology or nuclear research. The method was developed by bda connectivity and ensures reproducible results. Depending on the requirements, these cables can be supplemented with supply or power supply wires as well as additional shields. Type:MXR 0,48L/2,95 Product Number:1207 Purpose of use:Measurement technology div. applications Jacket material:PVC Country of origin:Germany...

...Tilt angle values of a platform stand for important measuring data as a part of the safety and control system of machinery. Angular measurement is, for instance for equipment levelling, performed in such cases by means of dual axis pendulum systems. Transducers of that type contain inside a robust splash-proof aluminium case of protection degree IP 65 to IP 68 oil-damped pendulum systems, the...

...Digital microscope camera for full-color-images and video recording of your samples in Full-HD: With 10-megapixel-CMOS-sensor and up to 30 pictures per second. The high-performance CMOS image sensor provides maximum image quality even in unfavorable light conditions and lower magnifications. Adaptation of the optimal exposure time, gamma and various other camera settings in almost any situation due to the intelligent automatic mode. Simple data transfer and video recording in Full-HD direct on the SD card.

... used in almost all industrial sectors, such as medical technology, pharmaceuticals, food and cosmetics industries, automotive, and electrical engineering. Feeding is an essential component in automation technology, just like the separation and provision of individual components. In addition to simple feeding systems, the expansion to complex testing, measuring, or assembly processes is possible. The combination of different feed systems is not a problem with the use of robots and handling systems. There is a seamless transition from simple parts feeding to a compact feeding and testing cell.

...We offer you standardised complete systems for the measurement of volume & mass flows. The EP LMF®-LaminarMasterFlow® is a complete system for high-precision flow measurement of gases and air. The LMF® system consists of a flow processor, a Laminar Flow Element (LFE) as measuring section, a cable set and a sensor package. The flow measurement is performed by means of Laminar Flow Elements (LFE), which are available in different sizes and cover a measuring range from 0.01 to 700 m³/h. (optionally up to 4000 m³/h).

...CEH – Calibration Engineering Hohmann offers you not only sophisticated testing and measuring equipment for force and torque, but also the expert software required for this.

...These series are specifically designed for maximum pressure monitoring in steam and hot water systems. It is a pressure switch "special design" with a self-monitoring pressure sensor, built according to the Pressure Equipment Directive DGR 2014/68/EU. It can be used as a pressure monitor or pressure limiter for maximum pressure monitoring (systems according to TRBS, according to DIN EN12828), for systems according to DIN EN12952-11 and DIN EN12953-9, and is available with or without differential adjustment. SIL 2 according to IEC 61508-2...

... design and simple, user-friendly operation ● Shock and vibration resistant due to an optimised sensor arrangement and balanced weight distribution ● Various operator level settings Size (W x L x H):450 x 400 x 720 mm (17.72 x 15.75 x 28.35 Inch) Weight:25 kg / 55.12 lbs Supply Voltage:110 - 230 V / 50 - 60 Hz Input Power:max. 100 Watt Camera:customised 1 Camera, high resolution Measuring range:up to max. 130 mm (5.11“) outer diameter Measuring according to standards:IEC 60811 -201; -202; -203 LV112 (A Faktor) ICEA S-94-649...

... (seated position) Continuous height adjustment of the knee stabilizer (seated position) Continuous adjustment of the knee stabilizer via pneumatic springs (seated position) Continuous adjustment of the lever bar length Adjustment of the start position in 10° increments Very fine weight gradation in 1 kg increments Rotatable and tiltable SmartPanel with training software Measuring sensor for isometric measurements Measuring sensor for measurement of mobility Protective panel made of frosted glass Options Pre-installed network equipment in compliance with the German Medical Devices Act...

...The converter shown corresponds to our standard design. Upon request, we are happy to customize the housing, connections, and additional equipment to suit your individual application. Contact us! Together, we will develop the perfect ultrasonic converter for your specific measurement task. WORKING RANGE: 50...500 mm WORKING FREQUENCY: 305 kHz SWING CYCLES AT 1/2 ECHO VOLTAGE: approx. 7 OPERATING...

NUMERIK JENA develops, produces, and distributes measurement systems for distance, position, and angle detection worldwide, with the highest resolution and precision. Our products not only impress with their particularly compact dimensions but are also universally applicable due to their versatility. The outstanding features of our EPIFLEX sensor modules make it possible to integrate them into...

... involvement in strategy and concept development, we are also available to assist you with the concrete implementation of existing specifications as a pure development service provider. COMPETENCIES: Electronics development and Embedded Systems Linux & Microcontrollers – Product development from A-Z – Industrial Internet of Things (IIoT) – Sensor-to-Cloud – LoRaWAN – Sigfox – NB-IoT ABOUT US...

... devices. Graduated accuracies allow the use of LK CMMs in laboratories, measuring rooms, and production. The sensor technology includes the complete Renishaw program as well as the entire NIKON laser series. Equally innovative is LK's software CAMIO, the first software specifically developed for CMMs. Our technologies support the entire process chain – from design, development, manufacturing, and assembly to quality assurance in global industries such as automotive, aerospace, defense, motorsport, energy, medical technology, and contract measurement.

...measuring machines for accuracy testing and cutting tools, accessories and services, multi-sensor coordinate measuring machines, surface testing devices, surface roughness measuring devices, optical measurement technology, non-contact profile measuring devices, testing equipment monitoring, shaft measuring machines, and much more.

... accurate measurement systems, and bionically inspired assistive robots. The measuring devices for characterizing the mechanical properties of surfaces at the micro level are distinguished by a high degree of automation, precise measurement ranges up to 100 mN, and individual configurability. In the in-house application laboratory, innovative materials from medical technology, photonics, the automotive industry, and general materials research are professionally characterized. The results enable significant savings potential through optimal material pairing of two moving bodies (e.g., piston and cylinder).

...IRIS GmbH has been a recognized and competent partner for industrial measurement technology for over 25 years in the following areas: • Infrared measurement technology • Flow sensor technology • Oil condition monitoring • Distance, position, and path measurement technology • Data collection/analysis We leverage our many years of practical experience in these fields to optimally...

... well as fully automated analysis systems, complete the company's demanding product portfolio. Customer proximity, customer consulting, and the manufacture of measuring instruments of the highest precision and reliability form the company's credo.

Manufacturing of differential pressure sensors and electronic pressure measuring devices for use in ventilation and air conditioning technology.