shaft seal Germany

...without shaft seal Robust and casted casing CARTRIDGE UNIT for fast and easy maintenance Temperature up to 120°C (higher temperatures are possible) Close coupled, single stage, back-pullout-design Universal DIN/ANSI connection Suction port DN65 Discharge port DN50 Material:Stainless Steel 1.4401 (AISI 316) Rated speed in [rpm] at 50Hz /60Hz:3000 Suction port:DN 65 Discharge port:DN 50 Voltage in [V]:400/690 V CA triphasé Protection class:IP 55 Max. flow velocity in [m/s]:côté aspiration = 1 / côté refoulement = 3 Max. temperature for in [°C]:190/optional bis 300...

...The RWD design RA is a radial shaft seal in standard execution according to DIN 3760 Type A, featuring an elastomer outer casing and an inserted tension spring. The design is suitable for sealing rotating shafts against pressureless spaces or spaces with low pressure differentials. Standard elastomer materials are NBR or FKM; other materials are available upon request.

...universal useclamping/release elastomer seal lightweight construction small size PRESSURE MAXIMUM 9,0 bar air vacuum TEMPERATURE MAXIMUM 90 °C air MEDIA:air, vacuum SPEED MAXIMUM:200 1/min SIZE:DN 8 (1/4") M5...

...Applications at high speed and low pressure. With O‑ring as secondary seal for sealing in the groove base. Hygienic design without undercuts. No sump formation in front of the seal. Reduced heat buildup due to special lip design. Pressureactivated seal energization. The integrated wedge prevents the sealing lip turning inside out. Very long seal life due to high abrasion resistance. Material only generates low frictional force. Sealing lip does not stick to the mating surface even after prolonged shutdown...

... in the barrel pump and significantly increases service life. The barrel pump is available in stainless steel, polypropylene, and polyvinylidene fluoride. In the stainless steel version, the F/FP 424 can also be used in explosive areas. Advantages: - No seal wear - Optimal emptying of the inner tube - High service life - Low wear on guide bearing and shaft - Long lifespan of the bearings...

...iglidur® sealing lip bearing d1 [mm]: Quick and easy-to-mount polymer bushing made of iglidur® J (JDSM) or iglidur® V400 (VDSM) with clip-on radial shaft seal ring as sealing for the rotating shaft. Seals off against dirt, dust as well as all pressure-less media. Polymer bushing with clip-on radial shaft seal ring Sealing for rotating shaft Temperature application range like iglidur® J...

... seal the Uniline. The profile of the linear axis can be used with numerous commercially available fastening components. • Motor mounting with solid or hollow shaft • Strokes of over 3,000 mm • Sizes from 40 x 51.5 mm to 100 x 122.5 mm • Variants with long runner or multiple runners The linear guides of the Compact Rail product family guarantee excellent performance in terms of speed and lifespan...

...Magnetically Coupled Unlike the standard pump, these products feature a frictionless magnetic coupling. Oil leakage from a conventional wear-prone shaft seal is eliminated in these models. Applications —Installation in analyzers —Installation in flywheels —Gas technology Value for the Customer —Saves space and is ideal for system integration —High pumping speeds with small dimensions —Low final...

...The conveyance of highly viscous products is part of our technical expertise. Feed pumps must meet the requirements for a long useful life, low maintenance and wear-free operation. We at IFA Technology live up to this claim by installing the most suitable pump in each of our systems. We use all types of pumps, from centrifugal pumps to gear pumps and piston pumps. Depending on the type of medium and its application requirements, we can design and offer you the suitable shaft seal. This includes among others packing gland seals, mechanical seals or magnetic couplings.

...When handling explosive dusts or gases, our fans are equipped with a spark protection at the impeller inlet. Both the shaft seal and the drive train comply with the requirements of the European ATEX directives.

... surfaces perpendicularity of the seal faces to the rotation axis elastic contact of the sealing surfaces existence of a lubricating film between the two sealing surfaces Usually the sealing capability of the mechanical seal against shaft or housing is obtained with the secondary seals, as O-rings, bellows or boots In conjunction with the International Organization for Standardization (ISO) and their standards (ISO 3069), the German Industrial Standard (DIN) published proposals for standard mechanical seals with DIN EN 12756 (24960).

... done by means of a single-acting, internal mechanical seal which is lubricated by the mixing product or an additional fluid The agitator shaft is connected to the drive directly with a flange coupling inside the seal housing. By default, this agitator series is supplied with marine type propellers. Other mixing elements according to the mixing task upon request. Solutions correspond to those of the SPR, additionally mechanical seal in sealing housing. Other solutions for this series upon request.

...The stirrer seal or stirrer passage is a key component of a pressure or vacuum reactor. It ensures the tightness at the passage of the rotating stirrer shaft. Contact us!

...The pumps of the Universal Seal Series are internally geared rotary pumps that operate based on the displacement principle. This allows for use with highly viscous media. Due to the extremely wide range of flow rates, pressure, and temperature, this series is suitable for a variety of applications and media. The selection of materials and shaft sealing types ensures application-specific pump...

...We supply V-Seals and V-Rings in a total of 9 different variants. For shaft diameters ranging from 2.7 mm to over 4,000 mm. Standard materials available include NBR and FPM/FKM. Additional special materials such as EPDM, H-NBR, CR, MVQ, and PTFE, some of which are also available in FDA-compliant mixtures or ADI-free, are also deliverable. Our extensive inventory ensures short delivery times. Custom orders can sometimes be fulfilled on short notice.

...Robust housing made of aluminum or stainless steel - Shaft and ball bearings with shaft seal - Rotor with shaft, gearbox, and permanent magnets mounted in a pre-chamber - Sensor circuit consisting of ASICs with Hall elements and interface electronics housed in a closed main chamber - Detection of revolutions through absolute multiturn gearbox - For protection class IP 69K, the housing is...

...Shaft Seal ASP, FPM Shaft Seal ASP 12 x 22 x 6 FPM Outer Diameter: 22.00 mm Width: 6.00 mm Inner Diameter: 12.00 mm Type: ASP...

...Shaft seal, manufactured in a specially designed vulcanization mold. The metal and rubber material can be tailored to meet specific requirements. Rubber-metal connections can be produced in custom sizes, different geometries, and various materials.

...The V-ring is a rubber-elastic shaft and bearing seal. The special feature of this seal is the axially arranged sealing lip.

...Single seal, For smooth shafts, Direction-dependent, Cone spring seal Seal concept: Single seal For smooth shafts Direction-dependent Cone spring seal Counter ring G 9 (Standard for DR 620) all other counter rings combinable Compatible counter rings: G 4 G 5 G 6 G 7 G 50 G 60 G 61 G 9 Operating parameters: Shaft diameter d 10 – 38 mm Pressure p max. 10 bar Temperature t -35 °C to 160 °C Speed v 15 m/sec.

...The radial shaft seal (RWDR) is the most widely used sealing element worldwide for sealing rotating shafts under predominantly pressureless conditions. The first design of this type of seal was originally invented by Walther Simmer. Therefore, these seals are also known by the name "Simmerring," under which they became globally recognized. • High-pressure rotor seals • Radial shaft seals • V-rings • Gamma rings...

... bearings, can also accommodate radial loads and high speeds. They are high-precision units made up of stable outer rings, ball races, and one- or two-part inner rings. Type designations: 7602.. /7603.. (double-sided acting, restricted tolerances, with pressure angle α = 60°) 2344.. (double-sided acting, restricted tolerances) ZKLN.. (double-sided acting, with lip seal or gap seal, optionally paired) ZKLF.. (double-sided acting, with lip seal or gap seal, optionally paired, screwable) Axial cylindrical roller bearings ... consist of...

... Shaft: 1.1191 / 1.4404 Bearing Pin: 1.1191 / 1.4404 Seal Insert: NBR, EPDM, FKM, Fortelan/AU, MVQ, CSM Flange Drilling: TW Standard, PN 6, PN 10, Special Drilling Actuation: Hand Lever / Prepared for Manual Remote Control / Inch Closure Directive: DGRL 2014/68/EU FDA 177.2600 EC Regulation 1935/2004 A: 266.5 B: 262 C: 179 D: 175 E: 99 F: 134 G: 35 Nominal Diameter: 100 Wrench Size: 12 / 15...

...The rotary unions of the G series are designed for the flow of media at high temperatures. The special bellows are made of stainless steel specifically for this application and ensure a long, trouble-free lifespan even under heavy stress. The finely lapped graphite seal perfectly adapts—thanks to the flexibility of the bellows—to the finely lapped hardened steel seal of the rotating shaft. The two sintered graphite bushings enable optimal rotation along the axis without any issues.

...Lightweight - Maintenance-free (with aluminum pin caps) - Lifetime lubrication - Reversible Motor type: Asynchronous short-circuit rotor motor, IEC 34 (VDE 0530) Insulation class of the motor winding: Class B, IEC 34 (VDE 0530) Voltage: 230V / 50Hz (IEC 38); 115V / 60Hz (on request) Frequency: 50 Hz Shaft seal, internal: Double lip, NBR Protection class: IP64 Thermal protection: Bimetal switch Ambient temperature, single-phase motor: +10 to +40 °C Rated power, single-phase motor: 0.050 to 0.085 kW Rated torque, single-phase motor: 9.3 to 18.4 Nm Max. pipe length SL: 602 mm...

...For the conveying of explosive dusts or gases. Explosion-proof fans For the conveying of explosive dusts or gases, out fans are equipped with spark protection at the impeller inlet. Both the shaft seal and the drive train comply with the regulations of the European ATEX directives.

... Swinghandle model 1107 manufactured by Emka Beschlagteile is made out of a GF black polyamide construction. It consists of a shaft brass having mixing materials with seal characterized by zinc plated design. Additionally, the roundrods of the product is not available for usage if doorgauge is (Ts) > 4 mm Type:swing Applications:door Material:polyamide...

...Is cleaning your ground-level shafts a hassle for you? Then we recommend the LAPARO light shaft cover. Shafts of various types can be protected with precision and fit. It keeps pests, mice, leaves, and dirt at bay and is suitable for basement shafts as well as for all other openings such as exhaust and air conditioning shafts. The surrounding brush seal ensures even better sealing! Advantages: · High-quality design made of aluminum and stainless steel · High light and air permeability · Easy installation even on existing grating · Optional brush seal...

... forces. This makes them perfect for applications that have to withstand high loads and shocks and compensate for shaft bending or misalignment. In addition to conventional spherical roller bearings (which have no seal and have either a tapered or cylindrical bore), there are also application-specific variants developed for special requirements (e.g. sealed spherical roller bearings or bearings with optimised load ratings). Spherical roller bearings offer high performance and efficiency and are available in a wide range of sizes and designs.

...Extremely robust design for high bearing loads up to 100N • Specifically developed for the food and beverage industry • Stainless steel version 1.4401 (V4A) • EHEDG: Tested hygienic design • Ecolab: Certificate of resistance to cleaning and disinfecting agents • High-quality electronics up to 25000 impulses • High protection class IP67 all around and IP69K • Zero dead space radial shaft seal (PTFE) • Full connection protection at 10 VDC … 30 VDC • Optional: −40 °C … +80 °C...