flow form Germany

...Efficient use of waste heat (up to 1.000 °C) In many production processes waste heat occurs in form of hot air which is put out to the environment without any use. Very often these hot gases are contaminated air. On the other side clean (cold) air must be warmed up for the production process. In these cases cross flow heat exchanger can reduce the energy costs. The hot air stream will be...

...The autonomous pressure regulator type 8011 with a closed cap, in the form of a pressure reducer (downstream pressure regulator) or a flow limiter (upstream pressure regulator), is used in a wide range of process engineering control tasks. Media such as steam, liquids, gases, etc. can be perfectly controlled without auxiliary energy. Material: Fully made of stainless steel Body 1.4581 / 1.4408...

... least 0.5 mm on the heat transfer surface. The flow model concept in the thin film evaporator is based on the principle that a wake forms in front of each rotor blade. The fluid coming from the wake originates from a highly turbulent area and slips into the space between the rotor blade and the heating surface, resulting in intense heat and mass transfer. This leads to good evaporation performance even with viscous products.

... protocol Modbus RTU which has found the way in industrial communication as an open protocol. The Modbus protocol is based on a master Slave architecture with which up to 247 Slaves can be questioned by a master – the data will transfer in binary form. Features: — differential pressure from 10 mbar up to 20 bar — static pressure max. 400 bar — accuracy: 0.1 % FSO — output signal 4 ... 20mA / 2-wire — aluminium housing, die casting Optional Features: — output signal RS485 with Modbus RTU protocol — several process connections...

... temperature of the cooling chamber. The moisture stored in the warmer air condenses on the cold concrete surface through which black ice can form. Dangers through the exchange of warmer and colder air arise particularly in the area of locks. When, through repeated opening of the doors, condensation from the walls and ceilings falls on the floor and black ice forms, it can lead to accidents. In consequence of the effects of permanent cold, doors can freeze solid at the seals and be severely damaged.

...Whether point-specific or central, broad or in the extraction cabinet – optimized pollutant capture is a crucial component in protecting your breathing air. Knowledge of aerodynamic processes and flow optimization, combined with our extensive engineering experience in extraction and filtration technology, as well as the use of state-of-the-art three-dimensional simulation software, form the...

...With decades of experience, Wenz Kunststoff GmbH & Co. KG has established a name in the field of temperature control in recent years. In particular, the in-house developed and modified special temperature control systems of the CycleTemp Vario, CycleTemp Flow, and CycleTemp Impuls series offer users every form of special temperature control. From active to passive variable temperature control...

...Kaplan turbines are typically used for river power plants on calm waters. The blade angle runner blades (Kaplan blades) is adjustable. The pressure of the water flow, which is controlled by the guide vanes of the upstream wicker gate, can then be efficiently converted into energy. The bidirectional MANOY® system seal WP, type 444, in the form of a continuous ring was developed to protect the...

...Flow protection for contamination-free filling of Big Bags. No contamination of people and equipment from residual product during the filling process.

... the modular design, a quick format change is possible. The following dosing systems can be used: - Excentric screw pumps - Piston pumps - Hose pumps - Flow measurement Contact us and inquire about additional versions. Upon request, we can enhance the machine with further functions and develop your specific machine solution. Machine type: FEH...

... pallet flow, without putting too much stress on the edges. The goods are secured with minimal material usage, without being damaged. Another application is to use the film banderole as a label carrier. This enables the legally required traceability of the shipping unit.

...Another solution for the gentle sorting of flat caps is the SSF type sorting part conveyor. The sorting part conveyor operates entirely without compressed air and, due to its low wear, does not generate any plastic dust. Depending on the closure, it achieves a performance of up to 250,000 closures per hour, and that in a single lane. The subsequent vertical transport of the flat caps via a chain magazine or by air flow allows for a comparatively low construction height of the sorting system and flexible site selection.

...The 5A regulation valve is ideally suited for regulating the flow of gases and liquids. Due to its special design it is able to regulate and shut off media. The regulation valve is highly resistant to media due to the materials that are used, PP, PVDF and PFA.

...Regulation and limitation of the hot water temperature via a valve combination in the heating circuit of hot water preparation using gasket-free plate heat exchangers made of stainless steel. Manufactured in compact/module construction on a vibration-damping and sound-insulating steel frame, with piping made of St37.0 P235 TR as well as form and connection pieces St37.0, drinking water side made...

...SET Control is an additive for delaying the setting time of Rapid Set repair mortars. FLOW Control is an additive for liquefying Rapid Set repair mortars. FAST is an additive for accelerating the setting time of Rapid Set repair mortars. Properties: delay liquefy accelerate Delivery form: bag...

...The high-speed servo-hydraulic control of the mill screwdown closes the loop: The thickness values measured precise to the micrometre form the basis for quick and precise control. Vollmer offers solutions for all control concepts from simple feedback control through to complete mass flow control or Direct gap contol for rolling of wedge-shaped strip and in tandem mills. Vollmer supplies the...

...Different aspects such as productivity, assembly operations, material flow, type variety, setup times and space conditions influence the concepts of linear transfer systems and form the foundation for many flexible automated solutions and linear transfer systems of modular construction. A high level of accessibility and the resulting low-maintenance design can count as additional advantages...

...Forging lubricant for aluminium and non-ferrous metal Temperature Range 160 °C to 400 °C Properties and Advantages • promotes the metal flow during forming process resulting in optimal form filling and accurate, precise parts • perfect release • much cleaner forgings, hardly any residues • reduced cleaning effort • high surface quality • improvement of tool die life due to adhesion of protective graphites • various modifications available e. g. Graphitex® CR 25-9/14...

...Form parts can be manufactured with radial or axial knurling. These knurlings are applied during the pressing process or in subsequent machining.

... • +U+C • +AC • +U+C+AC • +AC+C • +A+C+AC • +U+C+AC+LC • +A+C+AC+LC Dimension Ranges • Plant Hamm: 1.5 mm – 30 mm • Plant Iserlohn: 6.0 mm – 42 mm • Profiles available upon request Packaging / Delivery Form • Crown stands • parallel or thread-wound coils • rings / large bundles • Other packaging options available upon customer request...

... boxes, trays, plastic containers, bundles, pallets, and bags within automatic conveyor systems. Vertical Lift SPF1S: Transport direction in “S” form. Outfeed side always opposite the infeed side. Vertical Lift SPF1C: Transport direction in “C” form. Outfeed side always on the infeed side. Vertical Lift:High performance Vertical Transport:Gentle transport of products Material flow across several levels:Intermediate buffering of several products possible...

...Block storage in channels in stationary and dynamic form, optimal for order picking and for order tours.

...- Dismantling - Transport to the new location - Professional reassembly - Updating of load signs We also provide the following services: - Repair and/or replacement of defective rack components - Inspection before recommissioning - CAD planning Additionally, the following are possible: - Dismantling of existing storage facilities - Expansion of existing storage facilities through planning, delivery, and assembly You can access our prepared online inquiry form via the provided link.

... tightness measurement of buildings with an envelope area of approximately 7,000 to 36,000 m² or a building volume of up to 440,000 m³. In addition to measuring large industrial and administrative buildings, it also allows for use in single-family and multi-family homes with one or two BlowerDoor fans. With the BlowerDoor MultipleFan system (3 fans), air tightness measurements can be conducted and recorded with an air volume flow of around 21,600 m³/h using the TECLOG software. Pressure measuring devices and controllers form a clear unit near the measuring device.

... unauthorized access We offer the right product for every application: - Temperature resistance from -40 to 550 °C - Customized flow properties: liquid to pasty - Final hardness: soft to hard-elastic - Transparent or colored - For manual and machine casting, processing time: extremely short (10 sec.) to 3 hrs. (depending on the product) - Processing form: warm or cold curing - 1- or 2-component systems available - 1 kg to 30 t per delivery...

... clamping system, molds can be easily changed on any type of machine. The permanent electromagnetic technology represents the safest form of magnetic clamping for molds, as no current flow needs to be maintained. The quick clamping system is also indefinitely safe in the event of power outages. It retains its state and only changes with a renewed current pulse. As a result, this system is inherently an energy-saving champion.

...Impressively silent: The new aerodynamic form of the fan cover of the compressor aggregates generates an extremely smooth operation with a low noise level. Thus the KK 70 Silent is a real pleasure to handle. Impressively durable: The sturdy design of the oil-free compressor aggregates and the innovative, closed crank housing ensure a long operating life. Impressively reliable: A big fine filter of the oil-free compressor aggregates provides an excellent filtration and a high air flow rate, even on a continuous-running operation of 100 %.

... for channelling the conveying material into the conveying stream, such as knife gates for derived timber products. Cyclones, filters or combinations of the two are used to separate the conveying material from the conveying stream. The economical conveying lengths lie between around 150 and 750 m. The loading of the conveying stream can amount to up to 5 kg/m³ and essentially depends on the grain size, density and form of the material to be conveyed.

... warehouse systems, or functions as an alternative to conveyor systems with continuous conveyors. For example, the MONOFLEX can form the ideal complement to the MULTIFLEX pallet shuttle system. This rail guided vehicle system from DAMBACH consists of high-performance transport carts and a twin rail track. The track is made from anodized aluminum, which is not only robust, but easy to install. Simple switches ensure good availability, even in the case of complex plant layouts. With a 1:1 distribution of the material flow...

... for the ProJet MJP series is suitable for a variety of applications, such as concept models, checking form and fit, functional prototypes, flow analyses, rapid tooling, fixtures and jigs, casting patterns, as well as medical applications requiring certifications according to USP Class VI and/or ISO 10993.