Thread standard: Metric, ISO DIN 13 Type: Machine tap Forma C, for blind holes, with spiral flutes Application: Overlengthed (long shank) L=150 Material of product: HSSE Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 900 N/mm2 Standard: DIN 371/376 Tolerance: ISO2/6H Tap for machine use and through holes. The spiral point pushes the chips ahead and prevents clogging of the flutes. Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials Correct lubrication is important for successful thread cutting and to decrease the wear of taps and dies. We recommend using our lubricants.
INTENSE SRL - TECNICHE DI ASSEMBLAGGIO
Italy
Thread standard: Metric, ISO DIN 13 Type: Hand tap, Form C, for through and blind holes, with straight flutes Application: For high-tensile materials Material of product: HSSE Surface treatment: no For materials: Wear resistant steel Tensile strength up to: 1000 N/mm2 Standard: DIN 352 Tolerance: ISO2/6H Set of 3 taps (taper, intermediate, finish). Three-piece hand taps- sets are used for regular threads with coarse pitch, as the thread profile area is larger than for fine threads and the force effects on the taps are greater. The advantage of three-piece hand taps is that the respective parts of a set share the cutting power: The taper tap (No. 1) (marked with one ring) removes 65 per cent of the thread profile and the intermediate tap (No. 2) (marked with two rings) removes 85 per cent. Pre-cutting and reworking with the intermediate tap (No. 2)
Request for a quoteINTENSE SRL - TECNICHE DI ASSEMBLAGGIO
Italy
High quality self-tapping ensat thread inserts. Made of ASIS 304 stainless steel Short version with three cutting holes, Ensat 307 standard Particularly designed for materials resistant to cutting and where you want to exclude any slight self-locking effect on the screw. With the same insertion torque, they exert a higher and better distributed cutting force compared to Ensat 302 inserts, having three cutting points instead of two. Also Ensat 307 inserts are shorter than Ensat 308 and therefore ideal on thinner materials These inserts are self-tapping and do not require pre-threading. They can be easily installed by screwing them into the appropriately sized hole using the installation tool They are usually used to enforce or repair threads in metallic materials with low shear resistance (metal alloys, aluminum, cast iron, plastic, castings, etc.).
Request for a quoteINTENSE SRL - TECNICHE DI ASSEMBLAGGIO
Italy
Thread standard: Metric, ISO DIN 13 Type: Machine tap Form B with spiral entry, for through holes Application: Overlengthed (long shank) L=120 Material of product: HSSE Surface treatment: no For materials: Unalloyed and low alloyed steel, non abrasive material Tensile strength up to: 900 N/mm2 Standard: DIN 371/376 Tolerance: ISO2/6H Tap for machine use and through holes. The spiral point pushes the chips ahead and prevents clogging of the flutes. Overlengthed (long shank), L=120 Our taps and dies are produced to the highest quality standards, to ensure precise quality threads. Wide range of hand, machine and rolling taps, dies and tools for cutting professional threads on various materials Correct lubrication is important for successful thread cutting and to decrease the wear of taps and dies. We recommend using our lubricants.
Request for a quoteINTENSE SRL - TECNICHE DI ASSEMBLAGGIO
Italy
Thread standard: Metric Fine, ISO DIN 13 Type: Hand tap, Form C, for through and blind holes, with straight flutes Application: For high-tensile materials Material of product: HSSE Surface treatment: no For materials: Wear resistant steel Tensile strength up to: 1000 N/mm2 Standard: DIN 2181 Tolerance: ISO2/6H Set of 2 taps (taper, finish). Two-piece hand taps- sets are used for fine threads with a smaller pitch than with coarse thread, as the thread profile surface is smaller than with coarse threads and the force effects on the taps are smaller. The advantage of two-piece hand taps is that the respective parts of a set share the cutting power: The taper tap (No. 1) (marked with a ring) removes 65 per cent of the thread profile and the and brings the thread into shape. The finishing tap (No. 3) has no ring marking and cuts the remaining thread profile to produce the 100% full and usable thread.
Request for a quote